Step 1
Drill two small holes on each side of the wooden hoops .
Step 2 FebruaryThen paint all your circles in black wood.
Step 3 MarchOnce your circles are dry, go google '' moon phases. '' If you find an image / graphic that shows in every phase of the moon pressure. This will help you to keep track of what each stage looks like .Then start painting each moon phase with the gray color. I have to give a little glitter, shine my gray moons.
Step 4 AprilIf your moon is dry, you can begin to connect them. To do this , simply cut a small piece of embroidery thread and feed each end on the back of your two wooden hoops . Then tie a knot in the front. Repeat this step until all the moons are connected .
Once all your moons are connected , go and some embroidery thread for '''' black moons at each end of your banner . This will create loops to hang your banner.
Minggu, 15 Desember 2013
Selasa, 12 November 2013
Step By Step How To Make A Toy Car Used Bottle Guide
Hardware Requirements:
- 1 piece of plastic bottles
- 4 piece crown corks (for tires)
- 2 pieces of straw
- Tape
How to:
(Adding a straw). 1.Holes bottle front and rear body
Break Part 2 of straw. Straws, an eye which had been cut in the last two bottles.
3.Turn the cap before masing2 perforated suction side.
Place 4.After crown straw. Straws and strips on a bit thick coat. End so that the tires are not easily separated.
5.Paste integral straw on the back of the car. During the processing of the car.
Best of luck!
- 1 piece of plastic bottles
- 4 piece crown corks (for tires)
- 2 pieces of straw
- Tape
How to:
(Adding a straw). 1.Holes bottle front and rear body
Break Part 2 of straw. Straws, an eye which had been cut in the last two bottles.
3.Turn the cap before masing2 perforated suction side.
Place 4.After crown straw. Straws and strips on a bit thick coat. End so that the tires are not easily separated.
5.Paste integral straw on the back of the car. During the processing of the car.
Best of luck!
Selasa, 05 November 2013
Step By Step How To Make Wooden Toy Cars
Hardware Requirements:
- Wood
How to:
1.First prepare the ingredients.
2.Split and cut wood with a circular saw type serkel model.
3.Give shape pattern on wood.
Wooden model 4.Tack given by Jet saw chainsaw.
5.cleaning the flat surface, so that the timber with glass paper alternator.
6.Gluing one with the other wood surfaces with wood glue.
Use 7.Shape, smooth body paper alternator glass.
8.Give holes with a drill.
9.Make a wheel with a wood lathe.
10.Sublimate the surface, after all phases with a fine sandpaper finish.
11.Finishing spray by spraying the surface with a compressor melamine.
Best of luck!
- Wood
How to:
1.First prepare the ingredients.
2.Split and cut wood with a circular saw type serkel model.
3.Give shape pattern on wood.
Wooden model 4.Tack given by Jet saw chainsaw.
5.cleaning the flat surface, so that the timber with glass paper alternator.
6.Gluing one with the other wood surfaces with wood glue.
Use 7.Shape, smooth body paper alternator glass.
8.Give holes with a drill.
9.Make a wheel with a wood lathe.
10.Sublimate the surface, after all phases with a fine sandpaper finish.
11.Finishing spray by spraying the surface with a compressor melamine.
Best of luck!
Senin, 28 Oktober 2013
Step By Step How To Make Homemade Gift Box Beautiful
Hardware Requirements:
- Rice Box (can be bought in the supermarket)
- Adhesive paper / double top
- Insulation / adhesive glue
- The wrapping paper can be replaced with a washcloth jg
- Article
- Pencil
- Knife charter
- As a band, small flowers, dolls, or something in a unique form flannel Suspended
How to:
Gift box shape, good for beginners or 1.Specify square triangle.
2.make box or model.
3.then cut the housing.
4.Shape and unite the configuration box with insulation.
5.if done? To stick a box or double top at the top of the box inside and out, and provide background information.
6.Then gently turn the gift box.
7.Give double bottom box jga edge and cover with white paper.
If the valve is substantially covered with wrapping paper and then give up beautiful decorations
Best of luck!
- Rice Box (can be bought in the supermarket)
- Adhesive paper / double top
- Insulation / adhesive glue
- The wrapping paper can be replaced with a washcloth jg
- Article
- Pencil
- Knife charter
- As a band, small flowers, dolls, or something in a unique form flannel Suspended
How to:
Gift box shape, good for beginners or 1.Specify square triangle.
2.make box or model.
3.then cut the housing.
4.Shape and unite the configuration box with insulation.
5.if done? To stick a box or double top at the top of the box inside and out, and provide background information.
6.Then gently turn the gift box.
7.Give double bottom box jga edge and cover with white paper.
If the valve is substantially covered with wrapping paper and then give up beautiful decorations
Best of luck!
Senin, 21 Oktober 2013
Step By Step How To Make A Simple Fan
Hardware Requirements:
- switch
- Black and red cable 1m
- 2 x 1.5 V
- The battery
- Dynamo
- Sheets - Sheets bottle Aqua
- Black insulation
- Screwdriver (+) and (-)
How to:
1.Put a 1.5 V battery in the battery compartment, then cut the bottom of the bottle and forms such as AQUA knives - knives, only 4 sections.
2.Wrap the son of red and black copper in the switch.
Buyer 3.Others battery nothings, the red wire to the (-) terminal of the battery and the black wire to the (+) of the battery first, but open to the buyer.
4 The battery cable is coupled, attached to the anchor member
5.Plug knife - knife on the alternator.
6.Make all conditions as previously directed.
Best of luck!
- switch
- Black and red cable 1m
- 2 x 1.5 V
- The battery
- Dynamo
- Sheets - Sheets bottle Aqua
- Black insulation
- Screwdriver (+) and (-)
How to:
1.Put a 1.5 V battery in the battery compartment, then cut the bottom of the bottle and forms such as AQUA knives - knives, only 4 sections.
2.Wrap the son of red and black copper in the switch.
Buyer 3.Others battery nothings, the red wire to the (-) terminal of the battery and the black wire to the (+) of the battery first, but open to the buyer.
4 The battery cable is coupled, attached to the anchor member
5.Plug knife - knife on the alternator.
6.Make all conditions as previously directed.
Best of luck!
Step By Step How To Make A Wooden Bowl
Equipment and materials required:
- A fresh wood
- An ax
How to make :
1.Slit wood through the middle of the wood.
2.Select the perfect piece of wood you want. Make 2 pieces of fruit in your assessment on the handle of the bowl , as shown
in the image. Do not cut too deep. Then cut pieces that you have created on the base of the handle , before you can do to make the image of the shell. Now handle future what you want based .
3.Doing sculpture continuously until you are satisfied with the shape of your dish.
4.for timber pieces in a bowl is long enough
Thus, the strategy if you are busy, always when you cut a little time with your record Newspapers plastic to make it moist and not dry as it would make it harder for you drier Now it's time for a bowl cut you with a knife, and it may take a little time to dedicate the sculpture forms and you will soon know if you do get your hands perfectly capable of this. there
5.Place your work in an open bag for over a week , because if you do not, your chances are wooden bowl
dry quickly and the wood will last split.Hal you need to do is to stay
Grinding of the shell with sand paper starts from the rough , then smooth .
Best of luck !
- A fresh wood
- An ax
How to make :
1.Slit wood through the middle of the wood.
2.Select the perfect piece of wood you want. Make 2 pieces of fruit in your assessment on the handle of the bowl , as shown
in the image. Do not cut too deep. Then cut pieces that you have created on the base of the handle , before you can do to make the image of the shell. Now handle future what you want based .
3.Doing sculpture continuously until you are satisfied with the shape of your dish.
4.for timber pieces in a bowl is long enough
Thus, the strategy if you are busy, always when you cut a little time with your record Newspapers plastic to make it moist and not dry as it would make it harder for you drier Now it's time for a bowl cut you with a knife, and it may take a little time to dedicate the sculpture forms and you will soon know if you do get your hands perfectly capable of this. there
5.Place your work in an open bag for over a week , because if you do not, your chances are wooden bowl
dry quickly and the wood will last split.Hal you need to do is to stay
Grinding of the shell with sand paper starts from the rough , then smooth .
Best of luck !
Sabtu, 31 Agustus 2013
Step By Step How To Make A Simple Fan
Materials needed :
- Switches
- Black and red cables 1m
- 2 batteries 1,5 V
- The battery
- Dynamo
- Blades - blades of aqua bottle
- Isolation Black
- Screwdriver (+) and (-)
How to Make :
1.Put a 1.5 V battery in the battery compartment, then cut the bottom of the bottle and forms such as aqua blades - blades, just 4 sections.
2.Wrap the copper red and black wires in the switch.
3.Other copper tacked on battery, the red wire attached to the pole (-) battery, and the black wire attached to the pole (+) battery cable first but opened, until you see the copper.
4.The cable has been connected battery is attached to the armature
5.Plug blades - blades on the dynamo.
6.Make sure all the circumstances as directed previously.
Good luck!
- Switches
- Black and red cables 1m
- 2 batteries 1,5 V
- The battery
- Dynamo
- Blades - blades of aqua bottle
- Isolation Black
- Screwdriver (+) and (-)
How to Make :
1.Put a 1.5 V battery in the battery compartment, then cut the bottom of the bottle and forms such as aqua blades - blades, just 4 sections.
2.Wrap the copper red and black wires in the switch.
3.Other copper tacked on battery, the red wire attached to the pole (-) battery, and the black wire attached to the pole (+) battery cable first but opened, until you see the copper.
4.The cable has been connected battery is attached to the armature
5.Plug blades - blades on the dynamo.
6.Make sure all the circumstances as directed previously.
Good luck!
Step By Step How To Make A Beautiful Wooden Bowl
Equipment and materials required :
- A fresh wood
- An ax
How to Make :
1.Slit the wood by taking the midpoint of the wood.
2.Select the ideal piece of wood and you like. Make 2 pieces of fruit according to your estimates to the handle of the bowl as shown
in the image. Do not cut too deep. Then sectioned pieces that you created earlier to form the basis of the handle you can make the picture of the bowl. Now grip bowl according to what you want.
3.Doing carving continuous until you are satisfied with your dish shape.
4.For carved wood pieces into a bowl takes a fairly long time,
so the strategy if you are busy, do continuously if you have a little time with your record store logs in plastic in order to keep it moist and not dry, as if it would make you more dry difficult to carve! Now it's time to carve a bowl with a carving knife you, and this may spend some time to form carving and you will soon find out if your hands quite adept at doing this.
5.Place your work in an open bag for more than a week, because if you do not do it, chances are your wooden bowl
will dry too quickly and the wood will last split.Hal you need to do is stay
sanding the bowl with sand paper starts from the rough and then use smooth.
Good luck!
- A fresh wood
- An ax
How to Make :
1.Slit the wood by taking the midpoint of the wood.
2.Select the ideal piece of wood and you like. Make 2 pieces of fruit according to your estimates to the handle of the bowl as shown
in the image. Do not cut too deep. Then sectioned pieces that you created earlier to form the basis of the handle you can make the picture of the bowl. Now grip bowl according to what you want.
3.Doing carving continuous until you are satisfied with your dish shape.
4.For carved wood pieces into a bowl takes a fairly long time,
so the strategy if you are busy, do continuously if you have a little time with your record store logs in plastic in order to keep it moist and not dry, as if it would make you more dry difficult to carve! Now it's time to carve a bowl with a carving knife you, and this may spend some time to form carving and you will soon find out if your hands quite adept at doing this.
5.Place your work in an open bag for more than a week, because if you do not do it, chances are your wooden bowl
will dry too quickly and the wood will last split.Hal you need to do is stay
sanding the bowl with sand paper starts from the rough and then use smooth.
Good luck!
Step By Step How To Make Candle Decorative Candle Of Time
Materials and Tools needed :
- Remnants of wax used (more colors, the better)
- Small size glass
- Wick candles (can be purchased at craft stores)
- Markers water proof
- Cutter
How to Make :
1.Slice Used to smooth wax granules like sand.
2.Decorative glass with writing or pictures with a waterproof marker.
3.Enter the wick while the wax flakes pour chopped fine earlier in the glass. Condense to a solid back and the wick upright. If you are multicolored candles, it can put wax flakes slices alternating with another color. Condense back up to full.
4.Now your candle wax appearance to be different than usual. More beautiful because it is packaged in a glass that has been painted with markers color water proof you.
- Remnants of wax used (more colors, the better)
- Small size glass
- Wick candles (can be purchased at craft stores)
- Markers water proof
- Cutter
How to Make :
1.Slice Used to smooth wax granules like sand.
2.Decorative glass with writing or pictures with a waterproof marker.
3.Enter the wick while the wax flakes pour chopped fine earlier in the glass. Condense to a solid back and the wick upright. If you are multicolored candles, it can put wax flakes slices alternating with another color. Condense back up to full.
4.Now your candle wax appearance to be different than usual. More beautiful because it is packaged in a glass that has been painted with markers color water proof you.
Step By Step How To make A Crafts Sandals Pinch Of Materials Used Paint
Materials and tools needed :
- Plain flip-flops
- Oil paint
- Varnish
- Brushes
- Pencil
- Hair dryer. If no, can use the fan.
How to Make:
1.Decide what image you want to paint over your old flip flops. Select the images that simple, that is not difficult if you are a beginner to paint a portrait of affairs. The pictures suggested as pictures of flowers, stars, leaves or hearts.
2.Use a pencil to make a drawing first.
3.Once your finished image created with a pencil. Now seal your image with oil paint using a brush. Populate field with color sandals until there is no field in the top of the sandal that looks empty.
4.After all the top pedestal colored flip flops, dry with hair dryer or can also with the help of a fan.
5.Once completely dry. Cover picture that you paint over the top of the sandal footwear you had with spray varnish. Use varnish in order to eventually become more shiny appearance. Then, re-dry.
- Plain flip-flops
- Oil paint
- Varnish
- Brushes
- Pencil
- Hair dryer. If no, can use the fan.
How to Make:
1.Decide what image you want to paint over your old flip flops. Select the images that simple, that is not difficult if you are a beginner to paint a portrait of affairs. The pictures suggested as pictures of flowers, stars, leaves or hearts.
2.Use a pencil to make a drawing first.
3.Once your finished image created with a pencil. Now seal your image with oil paint using a brush. Populate field with color sandals until there is no field in the top of the sandal that looks empty.
4.After all the top pedestal colored flip flops, dry with hair dryer or can also with the help of a fan.
5.Once completely dry. Cover picture that you paint over the top of the sandal footwear you had with spray varnish. Use varnish in order to eventually become more shiny appearance. Then, re-dry.
Step By Step How To Make Pinch Of Pretty Rag Time
Materials and Tools needed :
- Flip flops plain
- Patchwork
- pencil
- scissors
- Glue gun
- Knick-knacks supporters. Can use the rest of the buttons are large if there is.
How to Make:
1.Put your flip flops over patchwork. It's the point that you can make cuts in the size of flip-flops pattern to the base. Draw the pattern with a pencil, and scissors.
2.Following the pattern of your footwear neat scissors, match the size patchwork at the top of your flip flops footwear. Do not forget, give a little hole in the middle and the two left and right side that strap sandals tongs not block patchwork to be affixed.
3.Paste patchwork scissors and you have your last match at the top of the flip-flops footwear using a glue gun. Remember, be careful using this type of glue because if exposed hands will feel the heat. Press and trim patchwork to cover all parts of the flip-flops footwear before, except strap clip.
4.To the strap flip-flops that have not been exposed to the touch patchwork, you simply cut the leftover patchwork size 3 cm width and length can be customized with your big flip-flops.
5.Give the glue on the strap flip-flops, then wrap the rest of the neat patchwork that has been cut to a width of 3 cm was in flip flops strap you to cover all parts of the strap clip.
6.Once all parts of your flip flops neatly covered with patchwork, except the bottom of the sandal, now you just add sweetener accessories for your flip-flops. Attach buttons former multicolored large strap on one side of your flip-flops.
Good luck!
- Flip flops plain
- Patchwork
- pencil
- scissors
- Glue gun
- Knick-knacks supporters. Can use the rest of the buttons are large if there is.
How to Make:
1.Put your flip flops over patchwork. It's the point that you can make cuts in the size of flip-flops pattern to the base. Draw the pattern with a pencil, and scissors.
2.Following the pattern of your footwear neat scissors, match the size patchwork at the top of your flip flops footwear. Do not forget, give a little hole in the middle and the two left and right side that strap sandals tongs not block patchwork to be affixed.
3.Paste patchwork scissors and you have your last match at the top of the flip-flops footwear using a glue gun. Remember, be careful using this type of glue because if exposed hands will feel the heat. Press and trim patchwork to cover all parts of the flip-flops footwear before, except strap clip.
4.To the strap flip-flops that have not been exposed to the touch patchwork, you simply cut the leftover patchwork size 3 cm width and length can be customized with your big flip-flops.
5.Give the glue on the strap flip-flops, then wrap the rest of the neat patchwork that has been cut to a width of 3 cm was in flip flops strap you to cover all parts of the strap clip.
6.Once all parts of your flip flops neatly covered with patchwork, except the bottom of the sandal, now you just add sweetener accessories for your flip-flops. Attach buttons former multicolored large strap on one side of your flip-flops.
Good luck!
Step By Step How To Make A Simple Steam Engine
Materials needed :
- Bit of wire, for turbine shaft.
- Pipe, can be anything as long as it is bent and heat resistant.
- Several former tin drinks, to make the boiler (where heat the water to evaporate) and its burner.
- Glue or glue iron G.
- Paint, to enhance the results.
- Plywood, as its base plate.
- Nut bolts (should not wear this, can directly glue), to buffer the boiler.
- Spirits, to fuel burner.
For equipment we just need (equipment may not be complete, the risk can be broken hand):
- Hacksaw, for sawing plywood or tin.
- Cutter (Choose large enough to easily do it), to cut the cans.
- Pliers, for bending pipe.
- Scissors, to make turbine of thin tin plate.
How to Make :
1. Close all the holes in the tin first, then puncture in the skin of the hull at each end. Function 1 hole to fill holes while the heated water for 2 to remove the fumes. 1 hole can be given a piece of pipe to make it more organized once made ??the cover so that when the last steam evaporation process is not out of the entry of liquid fluid (water).
2. Create a suitable turbine "greet skills" as well as its own lid to be like the black and white image above.
3. Do not forget to glue each component to be connected unless the exhaust holes (exhaust) to absolutely no holes.
4. Make it from the burner cans.
5. Then paint and laid out as you wish and use the fill water to evaporate in advance and enjoy the sensation of pleasure.
- Bit of wire, for turbine shaft.
- Pipe, can be anything as long as it is bent and heat resistant.
- Several former tin drinks, to make the boiler (where heat the water to evaporate) and its burner.
- Glue or glue iron G.
- Paint, to enhance the results.
- Plywood, as its base plate.
- Nut bolts (should not wear this, can directly glue), to buffer the boiler.
- Spirits, to fuel burner.
For equipment we just need (equipment may not be complete, the risk can be broken hand):
- Hacksaw, for sawing plywood or tin.
- Cutter (Choose large enough to easily do it), to cut the cans.
- Pliers, for bending pipe.
- Scissors, to make turbine of thin tin plate.
How to Make :
1. Close all the holes in the tin first, then puncture in the skin of the hull at each end. Function 1 hole to fill holes while the heated water for 2 to remove the fumes. 1 hole can be given a piece of pipe to make it more organized once made ??the cover so that when the last steam evaporation process is not out of the entry of liquid fluid (water).
2. Create a suitable turbine "greet skills" as well as its own lid to be like the black and white image above.
3. Do not forget to glue each component to be connected unless the exhaust holes (exhaust) to absolutely no holes.
4. Make it from the burner cans.
5. Then paint and laid out as you wish and use the fill water to evaporate in advance and enjoy the sensation of pleasure.
Step By Step How To Make A Wallet Out Of Fabric
Tools and materials required :
- 2 pieces of fabric for the outside of the wallet, it's up to the desired size. Mine are 20cm x 12cm
- 2 pieces of fabric to the inside, the same size
- 1 piece zipper 20 cm, can be cut if too long
- Scissors, thread, pin
- Sewing Machine
How to Make :
1. Bring fabric lining inside good side facing up, zipper facing up, and the outer layer of the fabric good side facing down (so both sides meet each other good). Shifted so as not to use the help of a pin.
2. Then sewing, and through the fabric so that the good side facing out.
3. Then repeat steps 1 and 2 on the other side of the zipper.
4. Once sewn and reversed.
5. Unite each side of the outer fabric and good inside.
6. then sew the left and right edges.
7. Sew the top edge and also the lower edge, make sure the zipper is opened when sewing each edge. reserving a little to flip open cloth wallet (not stitched full).
8. Behind purse through the open space behind.
9. Close the gap that opens with stitching, input the inside, and the wallet is ready for use.
Good luck!
- 2 pieces of fabric for the outside of the wallet, it's up to the desired size. Mine are 20cm x 12cm
- 2 pieces of fabric to the inside, the same size
- 1 piece zipper 20 cm, can be cut if too long
- Scissors, thread, pin
- Sewing Machine
How to Make :
1. Bring fabric lining inside good side facing up, zipper facing up, and the outer layer of the fabric good side facing down (so both sides meet each other good). Shifted so as not to use the help of a pin.
2. Then sewing, and through the fabric so that the good side facing out.
3. Then repeat steps 1 and 2 on the other side of the zipper.
4. Once sewn and reversed.
5. Unite each side of the outer fabric and good inside.
6. then sew the left and right edges.
7. Sew the top edge and also the lower edge, make sure the zipper is opened when sewing each edge. reserving a little to flip open cloth wallet (not stitched full).
8. Behind purse through the open space behind.
9. Close the gap that opens with stitching, input the inside, and the wallet is ready for use.
Good luck!
Step By Step How To Make Cold Powder
Materials needed:
- Rice flour (1 cup)
- Yam flour (1 cup)
- Fragrant Water Moderation
How to Make:
Material No. 1 and 2 mixed into one, then mixed with material No. 3 while in roller-roller until creamed like making cookie dough, just being dense dough. The powder made ??round object like a lizard eggs kept in the sun to dry.
Good luck!
- Rice flour (1 cup)
- Yam flour (1 cup)
- Fragrant Water Moderation
How to Make:
Material No. 1 and 2 mixed into one, then mixed with material No. 3 while in roller-roller until creamed like making cookie dough, just being dense dough. The powder made ??round object like a lizard eggs kept in the sun to dry.
Good luck!
Step By Step How To Make Traditional Body Scrub For Whitening Face Naturally
- Rice Scrub
Rice is no stranger to use as an alternative to whiten skin naturally. Rice contains Squalid oil, vitamin C, and vitamin E. Rice is the most effective way to whiten skin is Japanese rice. The rice has a higher vitamin content that is more effective than local rice.
However, that does not mean you can not use local rice because local rice you can also use. To make a scrub of rice, prepare rice which will be made into a scrub suit your taste.
After that, wash and soak the rice. Puree rice by way of fine rice pounded and mixed with rose water. Shape the dough into small round - small and basking in the sun to dry.
Once dry, you can take some seeds and mix it with water until it becomes a paste for use on the face. Apply evenly to the face and let stand until dry, or about 30 minutes. After that, rinse with clean water. Do this regularly to get maximum results.
- Scrub Yam
Yam is one of the most widely used fruits for skin whitening products. The content of the yam pieces able lighten skin naturally. If you want to whiten skin with yam, you can make it yourself at home.
How to Make :
Prepare 1 piece of yam that has been peeled clean skin. Then, wash thoroughly and grated yam according to the amount you need. After that, apply the results of grated yam in the face evenly. Let stand about - about 40 minutes and wash thoroughly.
- Tomato and Lime
Both of these fruits contain vitamin C which is very high and also antioxidants that can reduce free radicals. Vitamin C is believed to brighten the skin pigment, so the skin becomes white. To make a facial scrub of tomato and lime, prepare 1 large tomato and a lemon. Cut tomatoes up into several parts.
Then put tomatoes in a blender and add the lemon juice. Once blended, the dough used as a mask on the face. Let stand for 30 minutes and rinse with water until clean. If your skin is sensitive because the vitamin C content of orange juice is high enough, you can use the tomatoes alone.
Good luck!
Rice is no stranger to use as an alternative to whiten skin naturally. Rice contains Squalid oil, vitamin C, and vitamin E. Rice is the most effective way to whiten skin is Japanese rice. The rice has a higher vitamin content that is more effective than local rice.
However, that does not mean you can not use local rice because local rice you can also use. To make a scrub of rice, prepare rice which will be made into a scrub suit your taste.
After that, wash and soak the rice. Puree rice by way of fine rice pounded and mixed with rose water. Shape the dough into small round - small and basking in the sun to dry.
Once dry, you can take some seeds and mix it with water until it becomes a paste for use on the face. Apply evenly to the face and let stand until dry, or about 30 minutes. After that, rinse with clean water. Do this regularly to get maximum results.
- Scrub Yam
Yam is one of the most widely used fruits for skin whitening products. The content of the yam pieces able lighten skin naturally. If you want to whiten skin with yam, you can make it yourself at home.
How to Make :
Prepare 1 piece of yam that has been peeled clean skin. Then, wash thoroughly and grated yam according to the amount you need. After that, apply the results of grated yam in the face evenly. Let stand about - about 40 minutes and wash thoroughly.
- Tomato and Lime
Both of these fruits contain vitamin C which is very high and also antioxidants that can reduce free radicals. Vitamin C is believed to brighten the skin pigment, so the skin becomes white. To make a facial scrub of tomato and lime, prepare 1 large tomato and a lemon. Cut tomatoes up into several parts.
Then put tomatoes in a blender and add the lemon juice. Once blended, the dough used as a mask on the face. Let stand for 30 minutes and rinse with water until clean. If your skin is sensitive because the vitamin C content of orange juice is high enough, you can use the tomatoes alone.
Good luck!
Step By Step How To Make Origami Paper Flower
Tools and materials required:
- Paperboard
- Paper asturo
- Decorative Paper
- Sticks to taste
- Scissors
- Glue
- Pencil
- ruler
- Term
How to Make:
1.Make flower pattern on paper asturo. Then the paper folded, cut into 2, and again cut into small pieces to size. Paper that has been cut out and then glued and taped to the stick shaft. Once the paper is folded down.
3.Use a ruler and pencil to make a flower leaf pattern on paper asturo. Paper scissors according to the pattern that was made. Make a circle with a period of 4 pieces. Large size, medium, and small.
4.Rekatkan smallest circle paper on stem sticks. Prepare a pattern that is so, then arranged to form a circle. Then continue with the remaining paste flower patterns on the flower pattern that has been prepared. Attach a large piece of the circle to the flower arrangement that has been assembled. Then attach the pieces are the size of the circle to the smallest circle.
5.Cut the decorative paper with a size of 5 cm in the longitudinal direction. Decorative paper cut in a circle attached to the rod that has been given a glue stick. Flower arrangement that has been made, then attached to the stem sticks. Press firmly to be attached.
6.Origami paper flowers you've finished and ready to be used as decoration.
Good luck!
- Paperboard
- Paper asturo
- Decorative Paper
- Sticks to taste
- Scissors
- Glue
- Pencil
- ruler
- Term
How to Make:
1.Make flower pattern on paper asturo. Then the paper folded, cut into 2, and again cut into small pieces to size. Paper that has been cut out and then glued and taped to the stick shaft. Once the paper is folded down.
3.Use a ruler and pencil to make a flower leaf pattern on paper asturo. Paper scissors according to the pattern that was made. Make a circle with a period of 4 pieces. Large size, medium, and small.
4.Rekatkan smallest circle paper on stem sticks. Prepare a pattern that is so, then arranged to form a circle. Then continue with the remaining paste flower patterns on the flower pattern that has been prepared. Attach a large piece of the circle to the flower arrangement that has been assembled. Then attach the pieces are the size of the circle to the smallest circle.
5.Cut the decorative paper with a size of 5 cm in the longitudinal direction. Decorative paper cut in a circle attached to the rod that has been given a glue stick. Flower arrangement that has been made, then attached to the stem sticks. Press firmly to be attached.
6.Origami paper flowers you've finished and ready to be used as decoration.
Good luck!
Step By Step How To Make Statue Of Soap
Materials needed:
- Soap or soap bars
- Knife table or can be replaced with a plastic knife for the cake (avoid using a sharp knife that can harm children)
- Ballpoint pen or pencil
- Water and a towel or tissue
How to Make :
1.Hold soap by hand and make sure the position as comfortable as possible. Use a knife to carve out areas that are not occupied by the hand. The most convenient way is to form a hand on the soap as shown above. It might help to trace a line to the hand soap and then carve it. Or it could also create other forms of appropriate children imagination, develop course. Examples such as Angry Birds form below baseline. After hand shape already seen, the child does not have to hold the soap in hand again. Continue to carve soap positioned in place by the child comfortable to do so. Put your hands back to the soap if necessary.
2.Shape accordance with that thought in the beginning (before the sample form of the hand).
3.The completed, the sculpture can be smoothed with wetted and rubbed gently with a towel or cloth.
4.Letting dried and finished.
Good luck!
- Soap or soap bars
- Knife table or can be replaced with a plastic knife for the cake (avoid using a sharp knife that can harm children)
- Ballpoint pen or pencil
- Water and a towel or tissue
How to Make :
1.Hold soap by hand and make sure the position as comfortable as possible. Use a knife to carve out areas that are not occupied by the hand. The most convenient way is to form a hand on the soap as shown above. It might help to trace a line to the hand soap and then carve it. Or it could also create other forms of appropriate children imagination, develop course. Examples such as Angry Birds form below baseline. After hand shape already seen, the child does not have to hold the soap in hand again. Continue to carve soap positioned in place by the child comfortable to do so. Put your hands back to the soap if necessary.
2.Shape accordance with that thought in the beginning (before the sample form of the hand).
3.The completed, the sculpture can be smoothed with wetted and rubbed gently with a towel or cloth.
4.Letting dried and finished.
Good luck!
Step By Step How To Make Flowers For Skin Lotion
Materials needed :
- 2 teaspoons of coconut oil
- 1 cup of boiled water
- 1 teaspoon of essential oil
- 2 tablespoons of flower petals and the cake is dried (can use roses, jasmine, or lavender)
How to Make:
1.Take dried flowers, place in bowl. Mix with boiled water. Put it in the oven for 30 minutes.
2.Remove from oven flower water, then grab some spoons and mix with coconut oil and essential oils. Stir for a few minutes until completely mixed water and oil.
3.Sweep on the skin. Essential oils usually take up to 5 minutes for absorption by the body.
Good luck!
- 2 teaspoons of coconut oil
- 1 cup of boiled water
- 1 teaspoon of essential oil
- 2 tablespoons of flower petals and the cake is dried (can use roses, jasmine, or lavender)
How to Make:
1.Take dried flowers, place in bowl. Mix with boiled water. Put it in the oven for 30 minutes.
2.Remove from oven flower water, then grab some spoons and mix with coconut oil and essential oils. Stir for a few minutes until completely mixed water and oil.
3.Sweep on the skin. Essential oils usually take up to 5 minutes for absorption by the body.
Good luck!
Step By Step How To Make Yo-Yo
1.Every half of the plastic yo-yo started as two parts: the part, which would bring the flat inner shaft is called the disk, and the outer spherical shell called (type butterfly yo-yo is the opposite, with a flat round disk and shell. This is done through the same process but on a separate assembly line). Plastic used to make the disc and put shells in the form of solid pellets into a large funnel with a screw in equally large. The outside of the funnel covered with a flexible strip called the band heaters, electric blankets are like narrow for a funnel. Each band will be getting warmer as the narrow funnel, and a screw pushing pellets into the bottom of the funnel, they become more and more fluid. This process ensures that the pellets will melt evenly and completely, which is very important for the next step. At the bottom of the funnel, screw pushing molten plastic into the mold through a tube called a gate.
2.In the mold is the form of the four discs and four shells, all connected to the gate. This mold has a valve, allowing hot air to be pushed out to the front of the plastic and make sure that the mold completely.
Wooden yo-yo made from wood that has been dried to ensure your own yo-yo will not change shape. Modern wooden model has two sections of wood connected by a metal shaft.
Because the mold is fully charged and because the plastic has completely melted and evenly, each shell and each disc will always be perfectly round and perfectly even have a weight distribution. Once the mold is filled, plastic holding for 17 seconds and cool down with a water-filled tube running along the outside of the mold. Then the mold, which is actually two parts clamped tightly together, releasing shells and parts, all connected by a filled plastic gate, to the assembly line to be formed to yoyo section.
3.In while molding line is to make yo-yo parts, axles cutting machine apart to connect them. The engine is fed a long piece of round metal. Exact length of the metal to make the shaft is inserted into clamp where it was cut. Pieces are then cut notched at both ends so it will grip the plastic.
4.After mold release palm shells and discs, a separate clip their workers, eliminating the extra plastic and snapped them together to make a piece. Each disk has a lip shell and matching the pieces are free. When the plastic is still slightly warm from the mold, the lip will snap together. Once tied, they will not release.
5.This part derived belts for machines called hot stamper. The hot stamper has a circular tray with cup-like holders around the side. Each holder of taking half yo-yo and spin into a heated press. Press any roll feed logo yo-yo will show to the top half of the yo-yo. Then pressed into half and heats logo, affixing logos. Another design using round inserts the appropriate logo into the disk and the shell so that the insert can be seen clearly.
6.Part to continues down the line on workers who put the axle in half and set it with a hammer. The next worker put the other half on top and set it with a hammer. Then assembled yoyo placed in the air-driven press. The press has a tray in the form of yo-yo and a metal plate that fits between the yoyo part. The metal plate has grooves cut to fit around the axle and the exact thickness of the gap between the manufacturer's specified parts. When the press fire, it's good to permanently secure the two parts of the axle and set the correct gap between sections.
7.So The yo-yo is now placed on the table with a coiled rope and cutter at one end and upright, with a few notches in it at the other end. The distance between the cutter and the exact length of erect length string for each manufacturer wants yo-yo. String is pulled from the spool through the notch in the upright, where he circled the shaft of the yo-yo. Then pulled back into the cut, cutter, and bound. Yo-yo then left her hanging from a string, which is organized by the notch in the upright, turning to the axle.
8.Swing the yo-yo moves down the line to a machine that resembles a miniature turntable. A worker puts yo-yo at the wheel, holding it down with one hand, holding the tension in the string with your other hand, and with a foot switch operated, rotating to the yo-yo string.
9.Packaging yo-yo for a card called skin. Leather cards are pieces of cardboard with the product attached to it with what appeared to be melted plastic wrap you see hanging in store displays. To package the way yo-yo's, a piece of card tucked under a piece of wood with a hole in it in accordance with the card below. A yo-yo dropped through each hole to card. This ensures correct placement on the card. The sheet is then moved to the feed roller machine plastic film over the entire sheet of card and yo-yo. The film is made of a special plastic that fits every shape and shrink when heated but not melted. Machine heats the plastic, tightly seal the yo-yo to the card. The machine then cut the sheet into individual cards and rotate them into the basket where they are collected and boxed for shipment.
Good luck!
2.In the mold is the form of the four discs and four shells, all connected to the gate. This mold has a valve, allowing hot air to be pushed out to the front of the plastic and make sure that the mold completely.
Wooden yo-yo made from wood that has been dried to ensure your own yo-yo will not change shape. Modern wooden model has two sections of wood connected by a metal shaft.
Because the mold is fully charged and because the plastic has completely melted and evenly, each shell and each disc will always be perfectly round and perfectly even have a weight distribution. Once the mold is filled, plastic holding for 17 seconds and cool down with a water-filled tube running along the outside of the mold. Then the mold, which is actually two parts clamped tightly together, releasing shells and parts, all connected by a filled plastic gate, to the assembly line to be formed to yoyo section.
3.In while molding line is to make yo-yo parts, axles cutting machine apart to connect them. The engine is fed a long piece of round metal. Exact length of the metal to make the shaft is inserted into clamp where it was cut. Pieces are then cut notched at both ends so it will grip the plastic.
4.After mold release palm shells and discs, a separate clip their workers, eliminating the extra plastic and snapped them together to make a piece. Each disk has a lip shell and matching the pieces are free. When the plastic is still slightly warm from the mold, the lip will snap together. Once tied, they will not release.
5.This part derived belts for machines called hot stamper. The hot stamper has a circular tray with cup-like holders around the side. Each holder of taking half yo-yo and spin into a heated press. Press any roll feed logo yo-yo will show to the top half of the yo-yo. Then pressed into half and heats logo, affixing logos. Another design using round inserts the appropriate logo into the disk and the shell so that the insert can be seen clearly.
6.Part to continues down the line on workers who put the axle in half and set it with a hammer. The next worker put the other half on top and set it with a hammer. Then assembled yoyo placed in the air-driven press. The press has a tray in the form of yo-yo and a metal plate that fits between the yoyo part. The metal plate has grooves cut to fit around the axle and the exact thickness of the gap between the manufacturer's specified parts. When the press fire, it's good to permanently secure the two parts of the axle and set the correct gap between sections.
7.So The yo-yo is now placed on the table with a coiled rope and cutter at one end and upright, with a few notches in it at the other end. The distance between the cutter and the exact length of erect length string for each manufacturer wants yo-yo. String is pulled from the spool through the notch in the upright, where he circled the shaft of the yo-yo. Then pulled back into the cut, cutter, and bound. Yo-yo then left her hanging from a string, which is organized by the notch in the upright, turning to the axle.
8.Swing the yo-yo moves down the line to a machine that resembles a miniature turntable. A worker puts yo-yo at the wheel, holding it down with one hand, holding the tension in the string with your other hand, and with a foot switch operated, rotating to the yo-yo string.
9.Packaging yo-yo for a card called skin. Leather cards are pieces of cardboard with the product attached to it with what appeared to be melted plastic wrap you see hanging in store displays. To package the way yo-yo's, a piece of card tucked under a piece of wood with a hole in it in accordance with the card below. A yo-yo dropped through each hole to card. This ensures correct placement on the card. The sheet is then moved to the feed roller machine plastic film over the entire sheet of card and yo-yo. The film is made of a special plastic that fits every shape and shrink when heated but not melted. Machine heats the plastic, tightly seal the yo-yo to the card. The machine then cut the sheet into individual cards and rotate them into the basket where they are collected and boxed for shipment.
Good luck!
Step By Step How To Make A Bike Out Of Bamboo
1. Cutting Bamboo
Cut off the bamboo as a bike frame material very easily, far different from steel or other metal cutting. We just need a regular saws, abrasives, epoxy resin and natural fibers. Next, show the next working step.
2. Assemble Frame
Connecting bamboo sticks that have been cut into the bike frame, is the most difficult step for the workshop participants. Each bamboo bike makers have different methods. There is a wrap around frame that has been assembled with natural fiber sheets. Others use the connection joints of steel.
3. Wrap Frame
To make the connection stronger frame, bamboo wrapped in cloth from natural fibers. The way the aviation industry in developing bamboo grafting techniques. Use of hemp fiber composite material previously dyed epoxy resin.
4. Original Bamboo More
There is a motto "original steel frame bike is". Steel frame of the bike is touted provide the best quality while driving. Riding a bamboo bike frame mentioned more comfortable.
Good Luck!
Cut off the bamboo as a bike frame material very easily, far different from steel or other metal cutting. We just need a regular saws, abrasives, epoxy resin and natural fibers. Next, show the next working step.
2. Assemble Frame
Connecting bamboo sticks that have been cut into the bike frame, is the most difficult step for the workshop participants. Each bamboo bike makers have different methods. There is a wrap around frame that has been assembled with natural fiber sheets. Others use the connection joints of steel.
3. Wrap Frame
To make the connection stronger frame, bamboo wrapped in cloth from natural fibers. The way the aviation industry in developing bamboo grafting techniques. Use of hemp fiber composite material previously dyed epoxy resin.
4. Original Bamboo More
There is a motto "original steel frame bike is". Steel frame of the bike is touted provide the best quality while driving. Riding a bamboo bike frame mentioned more comfortable.
Good Luck!
Step By Step How To Make A Simple Air Balloon
Tools and Materials Required :
- Wax paper 3 or 4
- Reed
- Wire
- Double tip (adhesive) or raffia
- Scissors
- Kerosene
- Tissue fabric
- Lighters
How to Make :
1.Shape the reed become like a circle and then tied using rope.
2.Bundle the wire on the reed to form a "+".
3.Cut wax paper to form dome mosque.
4.Paste each side of the wax paper using double tip.
5.The finished molded wax paper, glue it to the reed. So that the position of the reed as a basic balloon.
6.lightly mist the tissue using kerosene and tie in the middle of the wire.
7.Bring balloons in the open space. Hold the tip of the dome and burn tissue using matchsticks.
8.Waiting to inflate the dome and then the balloon will fly by itself.
9.Need to noted that the diameter of the dome must be greater as three times the diameter of the reed and conditioning your fire suit and a large tall dome.
Good luck!
- Wax paper 3 or 4
- Reed
- Wire
- Double tip (adhesive) or raffia
- Scissors
- Kerosene
- Tissue fabric
- Lighters
How to Make :
1.Shape the reed become like a circle and then tied using rope.
2.Bundle the wire on the reed to form a "+".
3.Cut wax paper to form dome mosque.
4.Paste each side of the wax paper using double tip.
5.The finished molded wax paper, glue it to the reed. So that the position of the reed as a basic balloon.
6.lightly mist the tissue using kerosene and tie in the middle of the wire.
7.Bring balloons in the open space. Hold the tip of the dome and burn tissue using matchsticks.
8.Waiting to inflate the dome and then the balloon will fly by itself.
9.Need to noted that the diameter of the dome must be greater as three times the diameter of the reed and conditioning your fire suit and a large tall dome.
Good luck!
Step By Step How To Make A Tissue Box
Tools and Materials Required :
- Tissue
- Scissors
- Duct tape
- Isolation clear
- Paper wrapping
- Plastic
- Box. Boxes used should not be too thick, like cardboard but harder material than cardboard (if I use box cake).
How to Make :
1.Cut the box with cube pattern.
2.Cut the custom size paper with a tissue.
3.Shape the box, as boxes of food in general.
4.Shaped like a box or boxes of food for a snack, so his side was cut in such a way, so that the future can be safe.
5.Duct tape side-side so much glue.
6.Duct tape to strengthen its box shape.
How to Make a Tissue Cover:
1.Close wipes are made of paper of the same size with the size of the cube, but more 1 cm on each side.
2.Shape suburban box, as boxes of food in general.
3.Same like shape box, we make the linkages in addition, in order to form a tissue box cover.
4.Pasangkan box with lid.
5.Kita first tests the same box body the tissue box cover.
6.Put in tissue into the box.
7.Make the hole of pattern to your liking by using scissors.
8.Duct tape the box side. Close the tissue also dilakban, is expected to make it more sturdy. Blanket box with wrapping paper.
9.If the box look more beautiful, we cover tissue box with wrapping paper according to your taste, use a translucent insulation. Cover with plastic so that we are more durable tissue box, do not melt when exposed to water. Disposable plastic insulation glued to clear.
10.Close also covered the tissue wrapping paper and plastic disposable.
11.After your match results, enter the tissue.
Good luck!
- Tissue
- Scissors
- Duct tape
- Isolation clear
- Paper wrapping
- Plastic
- Box. Boxes used should not be too thick, like cardboard but harder material than cardboard (if I use box cake).
How to Make :
1.Cut the box with cube pattern.
2.Cut the custom size paper with a tissue.
3.Shape the box, as boxes of food in general.
4.Shaped like a box or boxes of food for a snack, so his side was cut in such a way, so that the future can be safe.
5.Duct tape side-side so much glue.
6.Duct tape to strengthen its box shape.
How to Make a Tissue Cover:
1.Close wipes are made of paper of the same size with the size of the cube, but more 1 cm on each side.
2.Shape suburban box, as boxes of food in general.
3.Same like shape box, we make the linkages in addition, in order to form a tissue box cover.
4.Pasangkan box with lid.
5.Kita first tests the same box body the tissue box cover.
6.Put in tissue into the box.
7.Make the hole of pattern to your liking by using scissors.
8.Duct tape the box side. Close the tissue also dilakban, is expected to make it more sturdy. Blanket box with wrapping paper.
9.If the box look more beautiful, we cover tissue box with wrapping paper according to your taste, use a translucent insulation. Cover with plastic so that we are more durable tissue box, do not melt when exposed to water. Disposable plastic insulation glued to clear.
10.Close also covered the tissue wrapping paper and plastic disposable.
11.After your match results, enter the tissue.
Good luck!
Step By Step How To Make Marbles
Materials needed:
- Marbles made ??of sand
- Lime soda
- Silica
- Various other materials used for pigment and design. In addition, there are also marbles made ??of glass culled and scrap.
How to make:
1.Melting
Sand, lime soda, and culled put in a large tank and heated until the temperature reaches 1260 degrees Celsius or 2300 degrees Fahrenheit. This could take as long as 28 hours.
2.Proses Injection
Then the melt was removed and transferred to a tank in which there is a hole to inject the melt. Marbles colors depending on the materials used. Of iron oxide green marbles, marbles from cobalt blue, and purple marbles derived from manganese. Speed ??and strength in the injection process will determine the final shape of the marbles.
3.Refrigerant & Cutting
In this process, the melt was issued in the form of lumps of glass. Clots that 'walk' under a slab of metal that will cut it into equal parts. Furthermore, these pieces will be sorted by hand.
Good luck!
- Marbles made ??of sand
- Lime soda
- Silica
- Various other materials used for pigment and design. In addition, there are also marbles made ??of glass culled and scrap.
How to make:
1.Melting
Sand, lime soda, and culled put in a large tank and heated until the temperature reaches 1260 degrees Celsius or 2300 degrees Fahrenheit. This could take as long as 28 hours.
2.Proses Injection
Then the melt was removed and transferred to a tank in which there is a hole to inject the melt. Marbles colors depending on the materials used. Of iron oxide green marbles, marbles from cobalt blue, and purple marbles derived from manganese. Speed ??and strength in the injection process will determine the final shape of the marbles.
3.Refrigerant & Cutting
In this process, the melt was issued in the form of lumps of glass. Clots that 'walk' under a slab of metal that will cut it into equal parts. Furthermore, these pieces will be sorted by hand.
Good luck!
Step By Step How To Make Butterflies Application Of Flannel Fabrics
Materials needed:
- Flannel Fabrics
- Uhu glue and wire (for the butterfly needle contrived)
How to make:
1.Cut the flannel suit existing form.
2.Shape and cut the wire to be used as needle-like butterflies (can also use a flower essence that was used to make plastic flowers).
3.Take the flannel sheets that have been cut, then glue the two sides in the middle.
4.Buckling the middle flannel.
5.Unite the edge over both bendable flannel cloth.
6.Give a glue in the center of the butterfly to stick tentacle.
7.And then his stick.
8.For beautify butterfly, you can give a decorative beads on the butterfly wings.
Good luck!
- Flannel Fabrics
- Uhu glue and wire (for the butterfly needle contrived)
How to make:
1.Cut the flannel suit existing form.
2.Shape and cut the wire to be used as needle-like butterflies (can also use a flower essence that was used to make plastic flowers).
3.Take the flannel sheets that have been cut, then glue the two sides in the middle.
4.Buckling the middle flannel.
5.Unite the edge over both bendable flannel cloth.
6.Give a glue in the center of the butterfly to stick tentacle.
7.And then his stick.
8.For beautify butterfly, you can give a decorative beads on the butterfly wings.
Good luck!
Step By Step How To Make A Cool Strap Watches
Tools and materials required :
- Para cord
- Watches
- Scissors
- Meter or ruler
- Cigarette Lighter
- Hemostats
- Side release Buckle 5/8
How to Make :
1.Measuring the para cord about 20 Inch, then cut.
2.Enter the step into this 3 hour long at the Buckle in the match with your watch.
3.Knit (weave) rope, the rope weave it should pull tight.
4.Cut the rest of the existing strap.
Good luck!
- Para cord
- Watches
- Scissors
- Meter or ruler
- Cigarette Lighter
- Hemostats
- Side release Buckle 5/8
How to Make :
1.Measuring the para cord about 20 Inch, then cut.
2.Enter the step into this 3 hour long at the Buckle in the match with your watch.
3.Knit (weave) rope, the rope weave it should pull tight.
4.Cut the rest of the existing strap.
Good luck!
Step By Step How To Create A Simple 3D Glasses
Materials needed:
- BLUE color mica paper (1 sheet)
- RED color mica paper (1 sheet)
- Carton former (minimum 30x5 cm)
How to Make:
1.Cutting shaped cardboard glasses model is up to you. add to use for nasal cavity.
2.Takle the plastic mica then shears BLUE glasses shape like a hole that you created earlier (Make the cuttings up to 2 sheets).
3.Take the red of color mica plastic then cut a hole formed as glasses that you created earlier (Make the cuttings up to 6 sheets).
4.Tide mica BLUE RIGHT next to the glasses on the hole (on the stack).
5.Tide mica glasses RED on the LEFT of the hole (in the stack).
- BLUE color mica paper (1 sheet)
- RED color mica paper (1 sheet)
- Carton former (minimum 30x5 cm)
How to Make:
1.Cutting shaped cardboard glasses model is up to you. add to use for nasal cavity.
2.Takle the plastic mica then shears BLUE glasses shape like a hole that you created earlier (Make the cuttings up to 2 sheets).
3.Take the red of color mica plastic then cut a hole formed as glasses that you created earlier (Make the cuttings up to 6 sheets).
4.Tide mica BLUE RIGHT next to the glasses on the hole (on the stack).
5.Tide mica glasses RED on the LEFT of the hole (in the stack).
Step By Step How To Make Acoustic Guitar
1. Early Stage (Making Body)
- Material from Cyprus wood and plywood
- Plywood cut to size length and then smoothed by using a machine. After a smooth inserted into the mold and clamped with a small clamp klose then mounted and dried. Once dry then fitted beige (the bones) with glue and dried again. After drying and plywood has been formed and released from mold then mounted crossbar. After installation is complete bolt and then installed large plywood on the front and rear using wood glue, then clamped with a large clamp and sun dried. Once dry plywood front and back cut following the shape of the guitar. The last process of this early stage is to establish the size of the hole resonance.
2. Neck making (Stang guitar)
- Made of mahogany, hibiscus or maple.
- Material dried in the sun or using the oven .. Wood then molded the shape Neck (Stang).
3. Splicing Body and Neck
- Neck geared body, after a suit then put together with glue and nailed. After that then crushed and placed fingerboard by using glue.
4. The smoothing process or putty
- After the body and neck mounted the stage to do next is the process of smoothing or putty guitar with coarse sandpaper, then in putty and sun dried. Once dry and then sanded back with sandpaper number 120 then part of the neck hole to attach strings then sending (tiner and hardener) twice and dried again. Once dry then sanded back with sandpaper number 240 to be more subtle.
5. Making Block (The String)
- Material from wood keeling formed according to the sample or to order desired (no benchmark). How to stick with using glue and screws. Form \ models depend series guitars will be produced.
6. Finishing or End Stage
- Painting, coated with melamine and dried in an oven that is not exposed to dust, Wiring (crepe), mounting block, mounting top and bottom (mainly made of plastic), installation of the list (of mica with castol glue or with large markers) , installation steamer, strings, brand.
Good luck!
- Material from Cyprus wood and plywood
- Plywood cut to size length and then smoothed by using a machine. After a smooth inserted into the mold and clamped with a small clamp klose then mounted and dried. Once dry then fitted beige (the bones) with glue and dried again. After drying and plywood has been formed and released from mold then mounted crossbar. After installation is complete bolt and then installed large plywood on the front and rear using wood glue, then clamped with a large clamp and sun dried. Once dry plywood front and back cut following the shape of the guitar. The last process of this early stage is to establish the size of the hole resonance.
2. Neck making (Stang guitar)
- Made of mahogany, hibiscus or maple.
- Material dried in the sun or using the oven .. Wood then molded the shape Neck (Stang).
3. Splicing Body and Neck
- Neck geared body, after a suit then put together with glue and nailed. After that then crushed and placed fingerboard by using glue.
4. The smoothing process or putty
- After the body and neck mounted the stage to do next is the process of smoothing or putty guitar with coarse sandpaper, then in putty and sun dried. Once dry and then sanded back with sandpaper number 120 then part of the neck hole to attach strings then sending (tiner and hardener) twice and dried again. Once dry then sanded back with sandpaper number 240 to be more subtle.
5. Making Block (The String)
- Material from wood keeling formed according to the sample or to order desired (no benchmark). How to stick with using glue and screws. Form \ models depend series guitars will be produced.
6. Finishing or End Stage
- Painting, coated with melamine and dried in an oven that is not exposed to dust, Wiring (crepe), mounting block, mounting top and bottom (mainly made of plastic), installation of the list (of mica with castol glue or with large markers) , installation steamer, strings, brand.
Good luck!
Step By Step How To Make the Bell House
Materials needed:
1. Outlet
2. 5 watt bulb blue color (color bias in select whatever you like)
3. Home Based Light Bulbs
4. Simple house bell
5. Kabel1-2meter
6. Jeck Cabel
7. Black scotch tape
8. Screwdriver Min (-) and Screwdriver (+)
9. scissors
How to Make:
1. Cut the cable to fit the need.
2. Connect the power cord with a bell that had been prepared earlier. (easy does not it? Stay in play only).
3. Reconnect the wires to the light bulb housing. Do the pairs bulb ago. Because it will complicate the installation of motion.
4. Connect the cables to the switch that had been prepared earlier, you must already know how to install a socket.
5. Attach the end of the cable into the cable head.
6. Done. Bel is ready. simple quiz...
Warning:
Do not ever polar unite on cable (- +). Must meet minus minus, Positive must meet positive. Because if the positive minus met, then there will be power surge when you are striking the bell.
1. Outlet
2. 5 watt bulb blue color (color bias in select whatever you like)
3. Home Based Light Bulbs
4. Simple house bell
5. Kabel1-2meter
6. Jeck Cabel
7. Black scotch tape
8. Screwdriver Min (-) and Screwdriver (+)
9. scissors
How to Make:
1. Cut the cable to fit the need.
2. Connect the power cord with a bell that had been prepared earlier. (easy does not it? Stay in play only).
3. Reconnect the wires to the light bulb housing. Do the pairs bulb ago. Because it will complicate the installation of motion.
4. Connect the cables to the switch that had been prepared earlier, you must already know how to install a socket.
5. Attach the end of the cable into the cable head.
6. Done. Bel is ready. simple quiz...
Warning:
Do not ever polar unite on cable (- +). Must meet minus minus, Positive must meet positive. Because if the positive minus met, then there will be power surge when you are striking the bell.
Step By Step How To Make Bottle Lantern
Materials needed :
- 12 pieces of bottle top
- 2 pieces of bottle caps
- 1 egg beads
- Ornament / tassel for hanging
- Yarn mattress
Tools needed :
- Cutter
- Scissors
- Stapler
- Other equipment (usually to pierce beads that covered the hole) to pierce the bottle cap or can also be used seam ripper, or whatever you want to pierce the bottle cap.
How to Make :
How to split and cut parts of this bottles, is by putting it in the bottle Pulpy orange pieces. Then cut parallel to the curve of the bottle (see arrows!). Scissors next to the distance past the 2 arches (arch orange peel), do not forget should be parallel to the grooves, and continue to do this for up to 5 again next part / parts.
Cut out this section, to the extent of the curve as above.
Do the same for the 12 piece pf the bottle.
Bending / folding to-5 parts, cut / split it out, if necessary, while the pleats pressed-press that position stabilized.
Once everything is bent, it would be like 'petals' are blooming.
And now we have a 12 'flower' plastic are blooming.
Combine one petal 'flower' to-1 with one petal 'flower' are all 2Lalu stapler on both sides. Take the 'flowers' the 3rd, and combine one petal 'flower' with one another petal of 'interest' to-1. Anyway, the five petals of 'interest' to-1 will be surrounded by the petals of 'interest' the other (5 'flower'). So everything will be 6 'flowers' are combined. The result looks like a half-round. But we have to make the same one again, in order to be round.
After the two are combined, see! so round right?
Punch a hole in the bottle cap first second the middle, not too big, at least not thread the mattress can be added to an existing hole in the ring. Bundle the decoration / yarn tassel with mattresses, the rest of the thread ties put in a bottle cap hole.
Knot two times or more, so that the thread can not exit / off. Put 1 bed sheet thread, about 25 cm or depending on the need to cap the second hole, the end of the thread on the inside of this cap is inserted into the hole of beads. Knot thread two times. Now lantern is complete, and you can hang it anywhere you like. It would be perfect if it were given a small light lanterns in it.
Good luck!
- 12 pieces of bottle top
- 2 pieces of bottle caps
- 1 egg beads
- Ornament / tassel for hanging
- Yarn mattress
Tools needed :
- Cutter
- Scissors
- Stapler
- Other equipment (usually to pierce beads that covered the hole) to pierce the bottle cap or can also be used seam ripper, or whatever you want to pierce the bottle cap.
How to Make :
How to split and cut parts of this bottles, is by putting it in the bottle Pulpy orange pieces. Then cut parallel to the curve of the bottle (see arrows!). Scissors next to the distance past the 2 arches (arch orange peel), do not forget should be parallel to the grooves, and continue to do this for up to 5 again next part / parts.
Cut out this section, to the extent of the curve as above.
Do the same for the 12 piece pf the bottle.
Bending / folding to-5 parts, cut / split it out, if necessary, while the pleats pressed-press that position stabilized.
Once everything is bent, it would be like 'petals' are blooming.
And now we have a 12 'flower' plastic are blooming.
Combine one petal 'flower' to-1 with one petal 'flower' are all 2Lalu stapler on both sides. Take the 'flowers' the 3rd, and combine one petal 'flower' with one another petal of 'interest' to-1. Anyway, the five petals of 'interest' to-1 will be surrounded by the petals of 'interest' the other (5 'flower'). So everything will be 6 'flowers' are combined. The result looks like a half-round. But we have to make the same one again, in order to be round.
After the two are combined, see! so round right?
Punch a hole in the bottle cap first second the middle, not too big, at least not thread the mattress can be added to an existing hole in the ring. Bundle the decoration / yarn tassel with mattresses, the rest of the thread ties put in a bottle cap hole.
Knot two times or more, so that the thread can not exit / off. Put 1 bed sheet thread, about 25 cm or depending on the need to cap the second hole, the end of the thread on the inside of this cap is inserted into the hole of beads. Knot thread two times. Now lantern is complete, and you can hang it anywhere you like. It would be perfect if it were given a small light lanterns in it.
Good luck!
Step By Step How To Make False Eyelashes Scarlet
1. Selection of raw materials. Scarlet only use human hair condition is selected at very tight.
Human hair was deliberately chosen as the raw material to be made ??false eyelashes really feel soft, supple and lightweight. In addition, the use of human hair will also make the wearer avoid the risk of irritation or allergy that can arise when the use of synthetic materials.
2. Making false eyelashes shape design that conforms to the shape eyes Indonesian women. This is important because women in Indonesia have different eye shapes vary so need false eyelashes are different also.
As an example; slanted eyes need false eyelashes caked or thickened on the outside. In contrast, large eyes requires individual types of false eyelashes that will make eyes lashes look more proportional.
3. Packing and labeling process. Each type of false eyelashes that are produced must be coded to facilitate the making of catalogs. After that every product will be included in the package and ready to ship.
Scarlet products has become a craze Indonesia since 1998 for women guaranteed in terms of quality, comfort and a variety of models to meet the needs of any Indonesian women.
Human hair was deliberately chosen as the raw material to be made ??false eyelashes really feel soft, supple and lightweight. In addition, the use of human hair will also make the wearer avoid the risk of irritation or allergy that can arise when the use of synthetic materials.
2. Making false eyelashes shape design that conforms to the shape eyes Indonesian women. This is important because women in Indonesia have different eye shapes vary so need false eyelashes are different also.
As an example; slanted eyes need false eyelashes caked or thickened on the outside. In contrast, large eyes requires individual types of false eyelashes that will make eyes lashes look more proportional.
3. Packing and labeling process. Each type of false eyelashes that are produced must be coded to facilitate the making of catalogs. After that every product will be included in the package and ready to ship.
Scarlet products has become a craze Indonesia since 1998 for women guaranteed in terms of quality, comfort and a variety of models to meet the needs of any Indonesian women.
Step By Step How To Make Toys From Used Tins
Tools needed:
- Paint cans or cans of milk a variety of sizes. We make different sizes of cans that tone that comes out is also different.
- Coins are no holes, when it was a coin 5 cents hollow middle.
- Rubber band.
- Wood fewer tall cans.
How to Make:
1. Rubber woven bracelet. Create two webbing for each coin. Tie two rubber woven bracelet was on the left and right side of the coin hole.
2. Fasten wood on either side of the tin, on top made ??somewhat prominent.
3. Fasten woven rubber bands existing coin cans clamped on wood, on both sides.
4. Fasten strong rope on a piece of wood that fits in the hole size coins. Adjust the strap length distance between us and the place where the cans will be placed. This wood serves as a barrier so that the coin is in the ready but not spinning operated.
5. Coin rotated so twisted rubber bands will participate.
6. Put logs that have been given a long leash, keep the rubber is twisted maintained.
Good luck...!
- Paint cans or cans of milk a variety of sizes. We make different sizes of cans that tone that comes out is also different.
- Coins are no holes, when it was a coin 5 cents hollow middle.
- Rubber band.
- Wood fewer tall cans.
How to Make:
1. Rubber woven bracelet. Create two webbing for each coin. Tie two rubber woven bracelet was on the left and right side of the coin hole.
2. Fasten wood on either side of the tin, on top made ??somewhat prominent.
3. Fasten woven rubber bands existing coin cans clamped on wood, on both sides.
4. Fasten strong rope on a piece of wood that fits in the hole size coins. Adjust the strap length distance between us and the place where the cans will be placed. This wood serves as a barrier so that the coin is in the ready but not spinning operated.
5. Coin rotated so twisted rubber bands will participate.
6. Put logs that have been given a long leash, keep the rubber is twisted maintained.
Good luck...!
Selasa, 27 Agustus 2013
Step By Step How To Make Helm
Materials needed:
- Helm former DMI type ( new guns also okay )
- ruler
- Buttons, buttons means that using that kind of rich fini ama Davida. Buy it in the store sewing / Taylor
- Solder
- Hammers, for install the buttons
How to Make:
1.Release all the parts on the helmet (glass, glass buffer) to bald.
2.Streak 3 points, the middle and the edge.
3.Solder 3rd point.
4.Pair the studs.
5.Pair the Pad.
6.Let added draw, just paint it (if needed).
7. Done!
- Helm former DMI type ( new guns also okay )
- ruler
- Buttons, buttons means that using that kind of rich fini ama Davida. Buy it in the store sewing / Taylor
- Solder
- Hammers, for install the buttons
How to Make:
1.Release all the parts on the helmet (glass, glass buffer) to bald.
2.Streak 3 points, the middle and the edge.
3.Solder 3rd point.
4.Pair the studs.
5.Pair the Pad.
6.Let added draw, just paint it (if needed).
7. Done!
Step By Step To Make Your Own Tattoo Machine
Tools needed:
- Dinamo former radio / walkman or may also use the dynamo tamiya ( cars toy Mini 4WD )
- Pens / pen (pen drawing Snoman) measuring 0.1 mm
- Adapter / charger may also use HP
- Cables small size
- Tablespoon
- Solasi
- String guitar
How to assemble:
1. Cut half that pen.
2. Connect the adapter to use a dynamo to solder if any pair switch on / off.
3. Discard the head of a spoon, then attach a pen / pen on the handle of a spoon with solasi.
4. bend the spoon handle 90 degrees to attach the dynamo as a needle mover.
5. Tie firmly with a spoon and the dynamo solasi.
6. Cut the guitar strings with sufficiently long.
7. Sharpen the end of the strings to be made tattoo needles.
- Dinamo former radio / walkman or may also use the dynamo tamiya ( cars toy Mini 4WD )
- Pens / pen (pen drawing Snoman) measuring 0.1 mm
- Adapter / charger may also use HP
- Cables small size
- Tablespoon
- Solasi
- String guitar
How to assemble:
1. Cut half that pen.
2. Connect the adapter to use a dynamo to solder if any pair switch on / off.
3. Discard the head of a spoon, then attach a pen / pen on the handle of a spoon with solasi.
4. bend the spoon handle 90 degrees to attach the dynamo as a needle mover.
5. Tie firmly with a spoon and the dynamo solasi.
6. Cut the guitar strings with sufficiently long.
7. Sharpen the end of the strings to be made tattoo needles.
Step By Step How To Make Your Own Incubator
Materials needed :
- Saws
- Hammer
- Gauge (meter/ ruler)
- Thermometer
- Thermostat
- Tray for water
ingredients :
- Plywood 3 mm in size 100 cm x 60cm
- Wood lath size of 3 cm x 4 cm
- Wire ram 1.5 meters
- Glass 2 mm (34 cm x 12 cm)
- 5 cm nail, nail plywood
- 8 pieces 5 watt bulb
- Hinges, wires, and plugs.
How to Make :
1. Pieces of wood lath with each length 60 cm = 8 pieces, 100 cm = 4 pieces for the frame.
2. Close sides using plywood.
3. Create also order for shelf space with the size of the egg:
- Length 940 mm
- Width 520 mm
- Thickness 20 mm wood
Attach the wire as a pedestal egg
4. Do not forget the side of the box to give ventilation. There is also a place in the top of the box. The same function, so that a change of air so as not stuffy inside.
5. Then make a door.
6. Attach fittings to place and Thermostat bulb at the ceiling.
Good luck!
- Saws
- Hammer
- Gauge (meter/ ruler)
- Thermometer
- Thermostat
- Tray for water
ingredients :
- Plywood 3 mm in size 100 cm x 60cm
- Wood lath size of 3 cm x 4 cm
- Wire ram 1.5 meters
- Glass 2 mm (34 cm x 12 cm)
- 5 cm nail, nail plywood
- 8 pieces 5 watt bulb
- Hinges, wires, and plugs.
How to Make :
1. Pieces of wood lath with each length 60 cm = 8 pieces, 100 cm = 4 pieces for the frame.
2. Close sides using plywood.
3. Create also order for shelf space with the size of the egg:
- Length 940 mm
- Width 520 mm
- Thickness 20 mm wood
Attach the wire as a pedestal egg
4. Do not forget the side of the box to give ventilation. There is also a place in the top of the box. The same function, so that a change of air so as not stuffy inside.
5. Then make a door.
6. Attach fittings to place and Thermostat bulb at the ceiling.
Good luck!
Step By Step How To Make Meatballs
Materials needed:
- 300 gr beef or minced chicken
- 3 Tablespoon flour Kanji (Tapioca Flour)
- 3 Fruit garlic, crushed / 2 teaspoon Garlic Powder
- 1 Item eggs, reserving whites only
- 1 teaspoon baking powder that expands well meatballs
- 1 teaspoon fine salt
- 1 Fruit maggi block
- Pepper powder to taste
- Nutmeg powder to taste
- Enough water to boil meatballs bulb
How to Make :
1. Stir all the above ingredients in a blender until well blended.
2. Stir well and gently. Repeat several times until smooth and creamy.
Tip: If it's too hard to blend in, give a little ice water.
3. After a smooth and evenly, shape into balls meatballs or bulb by using two small spoons.
If I create a meatball ball over too hard for you, these easy tips:
- Place the dough in the palm of the hand fist.
- Grasp like a fist and hit so compact.
- Remove the dough from the end of the fist (Between the thumb and index finger),
- Cut rounded with a small spoon.
- The result was not round as the meatballs were rounded up one by one, but the bulb rounding process much faster.
Good luck!
- 300 gr beef or minced chicken
- 3 Tablespoon flour Kanji (Tapioca Flour)
- 3 Fruit garlic, crushed / 2 teaspoon Garlic Powder
- 1 Item eggs, reserving whites only
- 1 teaspoon baking powder that expands well meatballs
- 1 teaspoon fine salt
- 1 Fruit maggi block
- Pepper powder to taste
- Nutmeg powder to taste
- Enough water to boil meatballs bulb
How to Make :
1. Stir all the above ingredients in a blender until well blended.
2. Stir well and gently. Repeat several times until smooth and creamy.
Tip: If it's too hard to blend in, give a little ice water.
3. After a smooth and evenly, shape into balls meatballs or bulb by using two small spoons.
If I create a meatball ball over too hard for you, these easy tips:
- Place the dough in the palm of the hand fist.
- Grasp like a fist and hit so compact.
- Remove the dough from the end of the fist (Between the thumb and index finger),
- Cut rounded with a small spoon.
- The result was not round as the meatballs were rounded up one by one, but the bulb rounding process much faster.
Good luck!
Step By Step How To Make A Rabbit Cage
Material for cages :
- Bamboo
- Wood / rafter
Standard size cage :
- Length 75 cm
- Width 50 cm
- Height 60 cm
Small size enclosure :
- Length 60 cm
- Width 40 cm
- Height 50 cm
How to make :
Bring all ingredients to form a cage according to what you want.
Good luck!
- Bamboo
- Wood / rafter
Standard size cage :
- Length 75 cm
- Width 50 cm
- Height 60 cm
Small size enclosure :
- Length 60 cm
- Width 40 cm
- Height 50 cm
How to make :
Bring all ingredients to form a cage according to what you want.
Good luck!
Step By Step How To Make A Fire Ball Can You Hold
Materials needed:
- Alcohol
- Ball tissue
- Marxist
How to Make:
1.Prepare 3 pieces tissue.
2.Roll the tissue form a ball.
3.Prepare the Alcohol and pour on top of the ball wipes that you will not grasp and hold.
4.Prepare a lighter. Fuel tissue balls that have been hit by alcohol, you have to hold part and not exposed to alcohol.
Good luck!
- Alcohol
- Ball tissue
- Marxist
How to Make:
1.Prepare 3 pieces tissue.
2.Roll the tissue form a ball.
3.Prepare the Alcohol and pour on top of the ball wipes that you will not grasp and hold.
4.Prepare a lighter. Fuel tissue balls that have been hit by alcohol, you have to hold part and not exposed to alcohol.
Good luck!
Step By Step How To Make Cat Doll Of Socks
Materials needed :
- Socks
- Dacron
- Sewing thread and embroidery
- Markers
- Scissors
- Needles
How to Make :
1. Behind socks and put the heel of the above.
2. Picture a cat's head on the end of the sock draw only part of his ear.
3. Image of curved lines before sewing with our direct puncture or stab trail use sewing machines, without cutting first so socks are not tangled.
4. If you've sewn our new 2-3mm piece of stitching. Remember how to cut to the base of the sock.
5. Then we cut down the head of a cat (part fingertips socks) to flip and fill, then behind a cat's head and set it aside for a moment.
6. We make the rest of the body Socks the cat, the cat's paw image bisects the upper end and the lower end of the line is approximately 5cm, then drawing a line to mark the circumference should be also stitched or sewn directly if you are impatient. function was to mark the beginning of the line to be cut.
7. Sewing sewing feet following the last dash, till all the top end and a closed bottom like the picture below and cut the rubber sock.
8. Cut the line that divides the two legs, remember do not let your stitches had come truncated.
9. Cut little cat stomach (upper sock heel okay?). Then turning back his socks.
10.Fill the head with dacron / silicon from both ears, while the contents sufficiently established that round. Content is also part of his body.
11. Just pull his head hole / shaved until the hole is closed connective dead.
12. Closed puncture hole with ladder stomach (almost like a running tap zigzag up and down every prick)
13. Put face stuffed with embroidery using wool yarn / thread embroidery.
14. If you already remove the end of the thread at the bottom of the head and tie a knot. Next for head to body with skewer stairs too.
15.The cat doll is already finished. If you want to add a tail, please try yourself.
Good luck!
- Socks
- Dacron
- Sewing thread and embroidery
- Markers
- Scissors
- Needles
How to Make :
1. Behind socks and put the heel of the above.
2. Picture a cat's head on the end of the sock draw only part of his ear.
3. Image of curved lines before sewing with our direct puncture or stab trail use sewing machines, without cutting first so socks are not tangled.
4. If you've sewn our new 2-3mm piece of stitching. Remember how to cut to the base of the sock.
5. Then we cut down the head of a cat (part fingertips socks) to flip and fill, then behind a cat's head and set it aside for a moment.
6. We make the rest of the body Socks the cat, the cat's paw image bisects the upper end and the lower end of the line is approximately 5cm, then drawing a line to mark the circumference should be also stitched or sewn directly if you are impatient. function was to mark the beginning of the line to be cut.
7. Sewing sewing feet following the last dash, till all the top end and a closed bottom like the picture below and cut the rubber sock.
8. Cut the line that divides the two legs, remember do not let your stitches had come truncated.
9. Cut little cat stomach (upper sock heel okay?). Then turning back his socks.
10.Fill the head with dacron / silicon from both ears, while the contents sufficiently established that round. Content is also part of his body.
11. Just pull his head hole / shaved until the hole is closed connective dead.
12. Closed puncture hole with ladder stomach (almost like a running tap zigzag up and down every prick)
13. Put face stuffed with embroidery using wool yarn / thread embroidery.
14. If you already remove the end of the thread at the bottom of the head and tie a knot. Next for head to body with skewer stairs too.
15.The cat doll is already finished. If you want to add a tail, please try yourself.
Good luck!
Step By Step How To Make A Socks
Materials needed:
- Used Socks
- Dacron or cotton dolls to content
- Thread
- Pearls for eyes and mouth stuffed
Tools needed:
- Scissors
- Tweezers
- Pen
- Pencil and needles.
How to Make:
1. Draw shapes on the bottom of a sock puppet for easier cutting, and accelerate your work. Cutting was its parts fit so neatly line.
2. Sew all the outskirts of the basic shapes, then fill the cotton or dacron on any part of the pieces to hold their shape well.
3. Stitch together all the sides so that it does not cotton or dacron out, here we already have all the basic parts of a doll filled with cotton / dacron, now live together all the parts and produced was a small stuffed panda from former socks.
Good luck!
- Used Socks
- Dacron or cotton dolls to content
- Thread
- Pearls for eyes and mouth stuffed
Tools needed:
- Scissors
- Tweezers
- Pen
- Pencil and needles.
How to Make:
1. Draw shapes on the bottom of a sock puppet for easier cutting, and accelerate your work. Cutting was its parts fit so neatly line.
2. Sew all the outskirts of the basic shapes, then fill the cotton or dacron on any part of the pieces to hold their shape well.
3. Stitch together all the sides so that it does not cotton or dacron out, here we already have all the basic parts of a doll filled with cotton / dacron, now live together all the parts and produced was a small stuffed panda from former socks.
Good luck!
Step By Step How To Make Butter Milk
Materials needed:
Pure milk, etc..
Tools needed:
Separator, Mortar, thermometers, etc..
How to make:
1. Head has been separated milk and pasteurized at a temperature of 70 ° C for 30 min or at 80 ° C for 1 min. Then cooled until it reaches room temperature.
2. Add as much as 3% starter and stir until blended. Leave at room temperature until a sour cream usually takes about 6 hours, and stored in the refrigerator, cooled to temperatures as low as minus 4 ° C.
3. After a cold and lumpy then pounded (churned) to separate the butter from the milk mashed ingredients (buttermilk). Ingredients butter washed with cold water (ice water) a few times to clean up the remnants of mashed milk.
4. Then the material is still high butter content it water to remove excess water, and butter grains into a more solid mass (compact). Required water content in the butter around 16-17%. Now done several times until the required moisture content is reached.
5. Once the water content meets, then added salt (table salt), stirring until blended 0.5-2%. After completion of salting butter wrapped. Natural color of butter obtained, because the cows in Indonesia are generally quite got food forages that contain lots of yellow carotene and fat-soluble.
Pure milk, etc..
Tools needed:
Separator, Mortar, thermometers, etc..
How to make:
1. Head has been separated milk and pasteurized at a temperature of 70 ° C for 30 min or at 80 ° C for 1 min. Then cooled until it reaches room temperature.
2. Add as much as 3% starter and stir until blended. Leave at room temperature until a sour cream usually takes about 6 hours, and stored in the refrigerator, cooled to temperatures as low as minus 4 ° C.
3. After a cold and lumpy then pounded (churned) to separate the butter from the milk mashed ingredients (buttermilk). Ingredients butter washed with cold water (ice water) a few times to clean up the remnants of mashed milk.
4. Then the material is still high butter content it water to remove excess water, and butter grains into a more solid mass (compact). Required water content in the butter around 16-17%. Now done several times until the required moisture content is reached.
5. Once the water content meets, then added salt (table salt), stirring until blended 0.5-2%. After completion of salting butter wrapped. Natural color of butter obtained, because the cows in Indonesia are generally quite got food forages that contain lots of yellow carotene and fat-soluble.
Step By Step How To Make Beaded Collar Necklace
Ingredients:
- Shirts / collared shirt
- Manik2 various sizes and types and crystal
- Needle
- Thread
How to Make:
Step 1: Cut off the collar of your shirt carefully and neatly
Step 2: It is recommended that put beads fit your design taste. Make sure the first motive is that you do not get confused when sew it.
Step 3: Begin sewing beads that you prepared earlier. Make sure that your stitches only in the top layer of fabric collar, so that the thread is not visible on the back side of the collar.
Step 4: Attach beads largest size instead of buttons. Make sure the size fits buttonhole and not too that are not easily separated when buttoned.
Good luck!
- Shirts / collared shirt
- Manik2 various sizes and types and crystal
- Needle
- Thread
How to Make:
Step 1: Cut off the collar of your shirt carefully and neatly
Step 2: It is recommended that put beads fit your design taste. Make sure the first motive is that you do not get confused when sew it.
Step 3: Begin sewing beads that you prepared earlier. Make sure that your stitches only in the top layer of fabric collar, so that the thread is not visible on the back side of the collar.
Step 4: Attach beads largest size instead of buttons. Make sure the size fits buttonhole and not too that are not easily separated when buttoned.
Good luck!
Step By Step How To Make Artificial Rain
Artificial rain by seeding clouds made ??using material that is hygroscopic (absorbs water) so that the grain growth process in the rain clouds will increase and will further accelerate the occurrence of rain. Cloud is used to make artificial rain is kind of cloud Cumulus (Cu) that looks like cauliflower. Once the location is known clouds, planes carrying special powder to fly to the clouds to rain.
The special powder composed of silver iodide glasiogenik form. Substance that serves to form ice. The aircraft also carries the powder to "merge" the drops in the cloud which is hygroscopic like salt or sodium chloride (NaCl), or CaCl2 and urea.
To be able to form a heavy rain, it usually takes as much as 3 tons of special powder that sowing to the Cumulus cloud for 30 days. Oh yes, the process of making artificial rain is not necessarily successful loh. Can fail or even a homemade rain falls in the wrong place when it was a big cost to manufacture. Therefore, the spread of seed rain should pay attention to the wind direction, humidity and air pressure.
Good luck!
The special powder composed of silver iodide glasiogenik form. Substance that serves to form ice. The aircraft also carries the powder to "merge" the drops in the cloud which is hygroscopic like salt or sodium chloride (NaCl), or CaCl2 and urea.
To be able to form a heavy rain, it usually takes as much as 3 tons of special powder that sowing to the Cumulus cloud for 30 days. Oh yes, the process of making artificial rain is not necessarily successful loh. Can fail or even a homemade rain falls in the wrong place when it was a big cost to manufacture. Therefore, the spread of seed rain should pay attention to the wind direction, humidity and air pressure.
Good luck!
Step By Step How To Make Children Clothing Patterns
1. Determining the size of Children Wear Pattern
This is better sew their own clothes, which we can set the size in accordance with what we want. Size is generally required for kids clothes patterns include:
* Circumference body, which is taken by wrapping the meter to the body, right under the armpit. The size of the amount plus as much as 4 cm.
* Waist circumference, taken with a tape measure wrapped around his waist, and add the amount as much as 2 cm.
* Long back, the measurement starts from the neck has vertebrae that protrude up to the waist.
* The width of the back, the measurement was widened in the back, from concave up to concave right arm left arm.
* The width of the face, the measurement was widened in the chest, right arm from concave up to concave left arm.
* Long shoulder, the measurement starts from the neck to the tip of the shoulder.
* Circumference concave arm, the measurement is done on the arm holes, and the amount added to 1 cm.
* Neck circumference, measurement is done by wrapping the meter on the neck.
* Long face, neck curvature measurement is done from the waist to the limit,
* Long sleeves, measurement is carried out from the lowest part of the shoulder to the sleeve length.
* Long dress, tailored to the measurement model to be made? ?.
2. Cutting Materials
Material is cut according to the pattern per pattern child dress to be made. Measure used is the result of measurements made at stage 1.
3. Kids Clothes Pattern Unification
Once all the material is cut to size and kids clothes pattern desired, then the next step is to put it together, with obras and sew.
Thus the process of making kids clothes, from design, to determine the pattern of kids clothes to incorporate process.
Good luck!
This is better sew their own clothes, which we can set the size in accordance with what we want. Size is generally required for kids clothes patterns include:
* Circumference body, which is taken by wrapping the meter to the body, right under the armpit. The size of the amount plus as much as 4 cm.
* Waist circumference, taken with a tape measure wrapped around his waist, and add the amount as much as 2 cm.
* Long back, the measurement starts from the neck has vertebrae that protrude up to the waist.
* The width of the back, the measurement was widened in the back, from concave up to concave right arm left arm.
* The width of the face, the measurement was widened in the chest, right arm from concave up to concave left arm.
* Long shoulder, the measurement starts from the neck to the tip of the shoulder.
* Circumference concave arm, the measurement is done on the arm holes, and the amount added to 1 cm.
* Neck circumference, measurement is done by wrapping the meter on the neck.
* Long face, neck curvature measurement is done from the waist to the limit,
* Long sleeves, measurement is carried out from the lowest part of the shoulder to the sleeve length.
* Long dress, tailored to the measurement model to be made? ?.
2. Cutting Materials
Material is cut according to the pattern per pattern child dress to be made. Measure used is the result of measurements made at stage 1.
3. Kids Clothes Pattern Unification
Once all the material is cut to size and kids clothes pattern desired, then the next step is to put it together, with obras and sew.
Thus the process of making kids clothes, from design, to determine the pattern of kids clothes to incorporate process.
Good luck!
Step By Step How To Make Paper Flowers Beautiful And Simple
Ingredients:
- Paper lime white and pink - lime and rare kinds of tissue paper. May be purchased at the shop or in the fresh flower shop selling goods birthday party.
- Scissors
- Gam various UHU or other
- Thread
How to Make :
1. Take a piece of white paper and the 6 Live the Courant. Arrange overlapping and folding sorts for fans.
2. Tie with yarn middle, cut on the left and right to be rounded or sharp form.
3. Embed the gam on the edge and develop.
4. Open each layer slowly so that it becomes a flower.
5. To make the center of the flower, pink paper folding.
6. Cut the meetings but not to drop out. Gam his right in the middle of the flower.
Good luck!
- Paper lime white and pink - lime and rare kinds of tissue paper. May be purchased at the shop or in the fresh flower shop selling goods birthday party.
- Scissors
- Gam various UHU or other
- Thread
How to Make :
1. Take a piece of white paper and the 6 Live the Courant. Arrange overlapping and folding sorts for fans.
2. Tie with yarn middle, cut on the left and right to be rounded or sharp form.
3. Embed the gam on the edge and develop.
4. Open each layer slowly so that it becomes a flower.
5. To make the center of the flower, pink paper folding.
6. Cut the meetings but not to drop out. Gam his right in the middle of the flower.
Good luck!
Step By Step How To Make Pecan Oil
Required equipment is :
- Big round of steel or Teflon, so it does not make sticky.
frying-blade or spoon made ??of wood
- Blender,
- Clean cotton cloth
- Cooker.
How to Make :
first wash and then drain the pecan nut. Combine hazelnut beans and water into a blender and process until smooth. Prepare a frying pan and clean cotton cloth, strain the seeds pecan and water solution with a cloth slightly. Juicing up the waste left in the fabric. Discard pulp hazelnut, while we are cooking liquid into oil. Turn on the stove over low heat, place the fryer contains clear solution pecan nut on it. Stir gently until the solution turned into a hazelnut seed oil. Cook until completely cooked, typically there is sediment in the bottom of the frying chocolate hazelnut oil signifying really mature. Then turn off the stove and wait for it to cool and settle hazelnut oil. Prepare a clean glass bottle and dry, hazelnut oil filter with a clean cloth into a bottle or in a glass bowl first. Only later inserted into the bottle through a funnel. Save hazelnut oil in a medium temperature and can be used for approximately 3 months.
How to make walnut oil is a recipe inherited from ancestors who sometimes has its own variations. There are mixing other ingredients when cooking solution hazelnut seeds in a frying pan. The ingredients were mixed among other leaf patchouli, ylang or jasmine. This is to add to the fragrant aroma of hazelnut oil and also to increase the benefits. Like patchouli leaves are also beneficial for hair fertility.
Good luck!
- Big round of steel or Teflon, so it does not make sticky.
frying-blade or spoon made ??of wood
- Blender,
- Clean cotton cloth
- Cooker.
How to Make :
first wash and then drain the pecan nut. Combine hazelnut beans and water into a blender and process until smooth. Prepare a frying pan and clean cotton cloth, strain the seeds pecan and water solution with a cloth slightly. Juicing up the waste left in the fabric. Discard pulp hazelnut, while we are cooking liquid into oil. Turn on the stove over low heat, place the fryer contains clear solution pecan nut on it. Stir gently until the solution turned into a hazelnut seed oil. Cook until completely cooked, typically there is sediment in the bottom of the frying chocolate hazelnut oil signifying really mature. Then turn off the stove and wait for it to cool and settle hazelnut oil. Prepare a clean glass bottle and dry, hazelnut oil filter with a clean cloth into a bottle or in a glass bowl first. Only later inserted into the bottle through a funnel. Save hazelnut oil in a medium temperature and can be used for approximately 3 months.
How to make walnut oil is a recipe inherited from ancestors who sometimes has its own variations. There are mixing other ingredients when cooking solution hazelnut seeds in a frying pan. The ingredients were mixed among other leaf patchouli, ylang or jasmine. This is to add to the fragrant aroma of hazelnut oil and also to increase the benefits. Like patchouli leaves are also beneficial for hair fertility.
Good luck!
Step By Step How To Make Flower Hair Tie From Flannel Fabrics
What is needed:
flannelet
flower petal pattern
needle
thread
rubber bracelets
scissors
former studs (for pistil)
(* You can wear rags if no flannel)
Step of manufacture:
1. * Create a pattern and cut according to the pattern flannel flower petals
* Leave the flannel and cut the size of a coin. Better to use black as a base color.
* After the cut according to the pattern, the pattern stitched into one to create long interest.
2. * Make sure the strands bond petals tightly.
* Then, glue or sewing on fabric base. At the end, together with how to sew at the bottom. So the interest is stronger and not easily separated.
3. * Create a connection of rubber or plastic and glue it to a rubber band.
* The link is then be sewn or glued. For stronger results, better sewn only.
4. * Finally, setup buttons former as the pistil.
* It may be glued, and trim in the center of the flower petals.
* Now, hair tie is not yet ready for use. Let the glue dry and tightly glue the material, making it more robust and durable.
flannelet
flower petal pattern
needle
thread
rubber bracelets
scissors
former studs (for pistil)
(* You can wear rags if no flannel)
Step of manufacture:
1. * Create a pattern and cut according to the pattern flannel flower petals
* Leave the flannel and cut the size of a coin. Better to use black as a base color.
* After the cut according to the pattern, the pattern stitched into one to create long interest.
2. * Make sure the strands bond petals tightly.
* Then, glue or sewing on fabric base. At the end, together with how to sew at the bottom. So the interest is stronger and not easily separated.
3. * Create a connection of rubber or plastic and glue it to a rubber band.
* The link is then be sewn or glued. For stronger results, better sewn only.
4. * Finally, setup buttons former as the pistil.
* It may be glued, and trim in the center of the flower petals.
* Now, hair tie is not yet ready for use. Let the glue dry and tightly glue the material, making it more robust and durable.
Step By Step How To Make Shoes Of Pants
Materials needed to make this shoe is one of the pant leg, the following tutorial:
1. Prepare palms / soles (outside) shoes. There are many types and forms of shoe soles, we can buy it in stores industrial material provider. If in Jogja, sol can be bought in store "Liman". The price varies, but last I was there the price ranging from 2 thousand per pair (including the sol layer), depending on the material and style.
2. Place the cardboard soles on paper upside down, then make a pattern corresponding sol form. Then cut out cardboard 0.5 cm larger than the pattern.
3. Scissors 2 pieces of fabric as cardboard cartridge before using the cloth pants.
4. Create a shoe head. Size can be changed according to the desired size. Incidentally my size 40 feet. The size of the head of his shoes as follows: scissors fabric and foam sheets fit the pattern above.
5. Prepare fabric (4 X 33 cm) to make elastic strap. Sewing fabric rubber tip on the end. Put the elastic band at the center of the fabric, then fold the fabric and sewing the edges (figure).
6. Sew straps on this shoe head
Then stack with foam, both part of the fabric facing each other, then sewing. Then turning, and sewing oppressed.
7. Place the head was to the fabric sol B. In order not to shift, with the needle hook. Then sewing the edges with a distance of 0.5 cm from the edge of the fabric into place flannel. Then sol A, and sewing all the edges with a distance of 0.5 cm from the edge of the incision in the middle of the fabric material.But sol A. Then behind the shoe through the hole, so that the head is outside shoes. then sewing the hole with glue. Give stitching section and the rear outer soles of shoes fabric. done starting from the edge of the center of the heel, Do it slowly and gradually so the results presentable. Make sure the seam is on the right edge of the fabric outer sole. After this, Allah willing, I plan to take it to the shoe cobbler, so sewn so much stronger.
8. Good luck.
1. Prepare palms / soles (outside) shoes. There are many types and forms of shoe soles, we can buy it in stores industrial material provider. If in Jogja, sol can be bought in store "Liman". The price varies, but last I was there the price ranging from 2 thousand per pair (including the sol layer), depending on the material and style.
2. Place the cardboard soles on paper upside down, then make a pattern corresponding sol form. Then cut out cardboard 0.5 cm larger than the pattern.
3. Scissors 2 pieces of fabric as cardboard cartridge before using the cloth pants.
4. Create a shoe head. Size can be changed according to the desired size. Incidentally my size 40 feet. The size of the head of his shoes as follows: scissors fabric and foam sheets fit the pattern above.
5. Prepare fabric (4 X 33 cm) to make elastic strap. Sewing fabric rubber tip on the end. Put the elastic band at the center of the fabric, then fold the fabric and sewing the edges (figure).
6. Sew straps on this shoe head
Then stack with foam, both part of the fabric facing each other, then sewing. Then turning, and sewing oppressed.
7. Place the head was to the fabric sol B. In order not to shift, with the needle hook. Then sewing the edges with a distance of 0.5 cm from the edge of the fabric into place flannel. Then sol A, and sewing all the edges with a distance of 0.5 cm from the edge of the incision in the middle of the fabric material.But sol A. Then behind the shoe through the hole, so that the head is outside shoes. then sewing the hole with glue. Give stitching section and the rear outer soles of shoes fabric. done starting from the edge of the center of the heel, Do it slowly and gradually so the results presentable. Make sure the seam is on the right edge of the fabric outer sole. After this, Allah willing, I plan to take it to the shoe cobbler, so sewn so much stronger.
8. Good luck.
Step By Step How To Make A Solar Bottle Lights
Ingredients:
1. Drinking water bottle is actually clear;
2. Sealant (silicone adhesive);
3. Patch material zinc;
4. Liquid laundry bleach;
Step work :
1. Make a circular hole in the middle of a piece of zinc with the size of 1 cm radius smaller than the radius of a bottle of mineral to be used. Position to choose the right center of the hole in the back on the zinc or zinc trench.
2. Then create a piece of 1 cm long, parallel to the radius of the hole, circular holes along the outer ring with the distance between pieces of 1 to 2 cm.
3. Bend towards the top of each piece, then put adhesive sealant (silicone) along the inner circumference side of the hole.
4. Put the bottle into the hole after selant dries, the head position at the top of the bottle, 2/3 of the bottle under the zinc and the third section is at the top of zinc.
5. Then glue and close the gap between the walls of the bottle and zinc using a sealant. It would be better if similar material coated with roofing cement or roofing coatings to be sure there are no leaks or open space.
6. Fill the bottle with clear water until it is full and mixed with a liquid laundry bleach bottle caps.
7. Cover again with the bottle gives sealant on the inside and outside of the bottle cap.
8. Then the holes zinc roof of the building at the planned position. Proper hole size with a circumference about the size of a bottle.
9. Provide sealant around the hole on, and when dry attach a bottle to match the water line on the zinc roof with zinc pieces attached to the bottle.
10. Close the gap between the pieces of zinc with zinc roofs with roofing cement material to prevent leakage during rain.
1. Drinking water bottle is actually clear;
2. Sealant (silicone adhesive);
3. Patch material zinc;
4. Liquid laundry bleach;
Step work :
1. Make a circular hole in the middle of a piece of zinc with the size of 1 cm radius smaller than the radius of a bottle of mineral to be used. Position to choose the right center of the hole in the back on the zinc or zinc trench.
2. Then create a piece of 1 cm long, parallel to the radius of the hole, circular holes along the outer ring with the distance between pieces of 1 to 2 cm.
3. Bend towards the top of each piece, then put adhesive sealant (silicone) along the inner circumference side of the hole.
4. Put the bottle into the hole after selant dries, the head position at the top of the bottle, 2/3 of the bottle under the zinc and the third section is at the top of zinc.
5. Then glue and close the gap between the walls of the bottle and zinc using a sealant. It would be better if similar material coated with roofing cement or roofing coatings to be sure there are no leaks or open space.
6. Fill the bottle with clear water until it is full and mixed with a liquid laundry bleach bottle caps.
7. Cover again with the bottle gives sealant on the inside and outside of the bottle cap.
8. Then the holes zinc roof of the building at the planned position. Proper hole size with a circumference about the size of a bottle.
9. Provide sealant around the hole on, and when dry attach a bottle to match the water line on the zinc roof with zinc pieces attached to the bottle.
10. Close the gap between the pieces of zinc with zinc roofs with roofing cement material to prevent leakage during rain.
Step By Step How To Make A Board Of Cardboard Used
Materials needed:
* 5 sheets of cardboard
* Quality wood glue
Equipment
* Floor, or other hard flat surface
* Board / plywood
* Stone is fairly heavy (you know?)
Well, now we start making :
1. Opened and flattened cardboard box, placed on the floor
2. Sprinkle one side with wood glue evenly
3. One Attach the other boxes on it, and on the side it covered again with wood glue
4. Take steps was repeated up to five boxes attached to each other.
5. Place the board / plywood on the box. Make sure the position is average, good, and true. Tap-tap to air out in between cardboard, and glue sticks very well.
6. Place the stone on top of plywood that can press and hold the plywood pile of boxes perfectly. Let stand until 2 or 3 days or until the glue dry completely. During settling, do not move the rock and plywood earlier.
7. Once the glue is dry (2 or 3 days), remove the stone and plywood. And you will get one piece cardboard (cardboard ply) are hard and strong, but easy to be processed.
8. Make a few sheets of cardboard, and you can make your dream bookshelf, or anything that you can make.
Good luck!
* 5 sheets of cardboard
* Quality wood glue
Equipment
* Floor, or other hard flat surface
* Board / plywood
* Stone is fairly heavy (you know?)
Well, now we start making :
1. Opened and flattened cardboard box, placed on the floor
2. Sprinkle one side with wood glue evenly
3. One Attach the other boxes on it, and on the side it covered again with wood glue
4. Take steps was repeated up to five boxes attached to each other.
5. Place the board / plywood on the box. Make sure the position is average, good, and true. Tap-tap to air out in between cardboard, and glue sticks very well.
6. Place the stone on top of plywood that can press and hold the plywood pile of boxes perfectly. Let stand until 2 or 3 days or until the glue dry completely. During settling, do not move the rock and plywood earlier.
7. Once the glue is dry (2 or 3 days), remove the stone and plywood. And you will get one piece cardboard (cardboard ply) are hard and strong, but easy to be processed.
8. Make a few sheets of cardboard, and you can make your dream bookshelf, or anything that you can make.
Good luck!
Step By Step How To Change Clockwise Being Left Turn
1. Disassemble the clock casing, and remove all the needles n do not get bent / damaged.
2. Removing the machine clock (the bolt in front of Gan, below the clock).
3. Open the machine and flipping coil core positions / coil / coil. In machine hours are not always the same and depends on the brand machine hours, sometimes you have to slice / modify / her even glue holder so that a stable core coil. The principle is to reverse the "core". Close the back engine hours.
4. Those numbers change the clock. In certain circumstances such as the example below, you only need to replace / swap the positions of the numbers 3 and 9. Better if you want to bother with making your own little lay out the numbers with the help Photoshop hour or Corel, etc.
5. Put needle, the needle must remember all 12 numbers. Then do not forget to attach the glass casing, battery n set at appropriate local time.
6. Completed.
2. Removing the machine clock (the bolt in front of Gan, below the clock).
3. Open the machine and flipping coil core positions / coil / coil. In machine hours are not always the same and depends on the brand machine hours, sometimes you have to slice / modify / her even glue holder so that a stable core coil. The principle is to reverse the "core". Close the back engine hours.
4. Those numbers change the clock. In certain circumstances such as the example below, you only need to replace / swap the positions of the numbers 3 and 9. Better if you want to bother with making your own little lay out the numbers with the help Photoshop hour or Corel, etc.
5. Put needle, the needle must remember all 12 numbers. Then do not forget to attach the glass casing, battery n set at appropriate local time.
6. Completed.
Step By Step How To Make Jelly Candy
Often times we see a variety of colors of jelly candy, jelly candy is usually liked by children and even adults also like the jelly candy. Actually you can also make your own at home, how to make also not too difficult. Let's try to make it .
Ingredients:
- 1 packet gelatin powder
- 100 grams of gelatin
- 260 grams of ice water
- 520 grams of sugar
- 190 grams of water
- 430 grams of glucose
- 10 grams of citric acid
- 10 grams of flavorings to taste
- Granulated sugar for sprinkling
- Vegetable oil to taste
How to Make:
* Enter the gelatin and agar-agar powder in ice water, soak for about 10 minutes.
* Next batter over the melted by the team in hot water.
* Enter the glucose and sugar in boiling water, boil until sugar dissolves.
* Enter the Ci-tic Acid stew sugar, stir well and let's make over low heat.
* Add flavorings and gelatin mixture, stir evenly.
* Prepare the mold, spread with cornstarch and sugar to prevent sticking.
* Print to mold and shape the dough according to taste. Printer can use ice-cube trays in the freezer.
* Allow a day in the mold, then remove and spread with vegetable oil sedition.
* Lastly, jelly candy with plastic wrap packaging.
Ingredients:
- 1 packet gelatin powder
- 100 grams of gelatin
- 260 grams of ice water
- 520 grams of sugar
- 190 grams of water
- 430 grams of glucose
- 10 grams of citric acid
- 10 grams of flavorings to taste
- Granulated sugar for sprinkling
- Vegetable oil to taste
How to Make:
* Enter the gelatin and agar-agar powder in ice water, soak for about 10 minutes.
* Next batter over the melted by the team in hot water.
* Enter the glucose and sugar in boiling water, boil until sugar dissolves.
* Enter the Ci-tic Acid stew sugar, stir well and let's make over low heat.
* Add flavorings and gelatin mixture, stir evenly.
* Prepare the mold, spread with cornstarch and sugar to prevent sticking.
* Print to mold and shape the dough according to taste. Printer can use ice-cube trays in the freezer.
* Allow a day in the mold, then remove and spread with vegetable oil sedition.
* Lastly, jelly candy with plastic wrap packaging.
Step By Step How To Make Soap
Every day we showered, and certainly in the bath we use soap, either solid or liquid soap.
Of course we also want to know, how to make the soap.
Well this time Handicrafts Home Industry presents how to create solid or bath soap bars.
Here we go, first we collect Materials needed:
- Oil or Fat - Almost all of the oil / natural fat can be made into soap. Find easy just like: Coconut Oil, Palm Oil, Olive Oil, Corn Oil, Soybean Oil ...
- NaOH / KOH - To change the oil / fat into soap. Could buy in a store chemicals, take a technical course.
- Water - As the catalyst / solvent. Choose distilled water or bottled water. Water from Pam is not good, many containing minerals.
- Essential and Fragrance Oils - As fragrances. Buy in store or other chemicals.
- Dyes - For coloring soap. Can also use food coloring.
- Additives - Spices, herbs, talc, starch / cornstarch can be added when the "trace".
Once the materials we complete the next step we prepare the tools needed:
- A simple mask - Used for making a solution of NaOH / KOH alone.
- Glasses - Used for the manufacture of NaOH / KOH alone.
- A pair of rubber gloves - Used for making soap.
- Plastic bottles - for water containers.
- Kitchen scales (the smallest scale 1 or 5 grams).
- Small plastic bags - To weigh NaOH / KOH.
- Stainless steel spoon or plastic-polypropylene - To pour NaOH / KOH and stirred.
- Containers of glass or plastic-polypropylene - To place a solution of NaOH / KOH with water.
- Containers of plastic - To weigh and where water and oil.
- Cain - To close the mold after it is soap.
- Thin plastic - To coat the mold.
- Mold - soap mold for printing according to your taste.
- Blender with lid.
- Cain - To close the blender.
Okay, after all the materials and equipments are complete following Directions:
Here is a simple recipe to make natural soap:
Ingredients:
Recipe # 1 - solid soap
- Olive Oil 235 g
- Coconut Oil 150 g
- 100 g Palm Oil
- 74 g NaOH - Sodium hydroxide + 210 g water
- 10 + cc fragrance dye
(Process At Room Temperature)
Recipe # 2 - solid soap
- Palm Oil 250 g
- Coconut Oil 140 g
- 100 g Corn Oil
- 75.5 g NaOH - Sodium hydroxide + 210 g water
- 10 + cc fragrance dye
(Process At Room Temperature)
Weigh the water and NaOH / KOH, according to the recipe. Dissolve NaOH / KOH into the water cool / cold (Do not use aluminum containers. Use stainless steel, pyrex glass or plastic-poliproplen). Do not pour water into NaOH / KOH. Pour the NaOH / KOH into the water little by little. Higga stir to dissolve. First of all the solution will be hot and whitish. Once everything is dissolved, in a safe place to be cooled to room temperature. Will obtain a clear solution.
Weigh oil (Coconut Oil, Palm Oil, Olive Oil, Corn Oil, Soybean Oil ...) according to the recipe.
Pour oil was weighed into a blender.
Carefully pour the solution in NaOH / KOH into the oil.
Put cover blender, put the cloth on top of the cover was to avoid splashing and processes at the lowest round. Lest Avoid splashing into your face or body. Stop the blender and check the soap to see the stage "trace". "Trace" is a condition in which the soap has been formed and is the end of the mixing process. The sign is when the soap mixture begins to thicken. When touched with a spoon, then spoon a few seconds before the former still made an impression, that's why it is called "trace".
At the time of "trace" before you can add fragrances, dyes or additives. Stir a few seconds then stop round blender.
Pour the soap results into a mold. Cover with a cloth for insulation. Keep the soap in the mold last for one to two days. Then remove it from the mold, cut to taste. Keep at least 3 weeks before use.
* Explanation of how the number 1 for safety.
Sodium Hydroxide (NaOH) / Sodium Hydroxide / lye / caustic soda / caustic soda is the main ingredient in the manufacture of soap other than oil. Through a chemical reaction, NaOH changed the oil or fat into soap. Addition of NaOH is also necessary to make shampoo and body lotion.
In making lye (NaOH + water), there are some things that should be considered include:
Use long sleeves, goggles, masks and rubber gloves. Precautionary principle - attention is necessary because the fluid can cause blindness if splashed in eyes, or cause a burning sensation on the skin when. Also provide vinegar, this is to anticipate when the skin is exposed to the alkaline liquid.
Do it in an open space, such as in a park or in a place that has free air. Do not breathe the air that comes out of this solution.
Always include into the water (slowly) and not vice versa. If you do otherwise, would result in outbreaks that are dangerous to skin and eyes.
Keep out of reach of children - children / do not involve children - children at all.
Of course we also want to know, how to make the soap.
Well this time Handicrafts Home Industry presents how to create solid or bath soap bars.
Here we go, first we collect Materials needed:
- Oil or Fat - Almost all of the oil / natural fat can be made into soap. Find easy just like: Coconut Oil, Palm Oil, Olive Oil, Corn Oil, Soybean Oil ...
- NaOH / KOH - To change the oil / fat into soap. Could buy in a store chemicals, take a technical course.
- Water - As the catalyst / solvent. Choose distilled water or bottled water. Water from Pam is not good, many containing minerals.
- Essential and Fragrance Oils - As fragrances. Buy in store or other chemicals.
- Dyes - For coloring soap. Can also use food coloring.
- Additives - Spices, herbs, talc, starch / cornstarch can be added when the "trace".
Once the materials we complete the next step we prepare the tools needed:
- A simple mask - Used for making a solution of NaOH / KOH alone.
- Glasses - Used for the manufacture of NaOH / KOH alone.
- A pair of rubber gloves - Used for making soap.
- Plastic bottles - for water containers.
- Kitchen scales (the smallest scale 1 or 5 grams).
- Small plastic bags - To weigh NaOH / KOH.
- Stainless steel spoon or plastic-polypropylene - To pour NaOH / KOH and stirred.
- Containers of glass or plastic-polypropylene - To place a solution of NaOH / KOH with water.
- Containers of plastic - To weigh and where water and oil.
- Cain - To close the mold after it is soap.
- Thin plastic - To coat the mold.
- Mold - soap mold for printing according to your taste.
- Blender with lid.
- Cain - To close the blender.
Okay, after all the materials and equipments are complete following Directions:
Here is a simple recipe to make natural soap:
Ingredients:
Recipe # 1 - solid soap
- Olive Oil 235 g
- Coconut Oil 150 g
- 100 g Palm Oil
- 74 g NaOH - Sodium hydroxide + 210 g water
- 10 + cc fragrance dye
(Process At Room Temperature)
Recipe # 2 - solid soap
- Palm Oil 250 g
- Coconut Oil 140 g
- 100 g Corn Oil
- 75.5 g NaOH - Sodium hydroxide + 210 g water
- 10 + cc fragrance dye
(Process At Room Temperature)
Weigh the water and NaOH / KOH, according to the recipe. Dissolve NaOH / KOH into the water cool / cold (Do not use aluminum containers. Use stainless steel, pyrex glass or plastic-poliproplen). Do not pour water into NaOH / KOH. Pour the NaOH / KOH into the water little by little. Higga stir to dissolve. First of all the solution will be hot and whitish. Once everything is dissolved, in a safe place to be cooled to room temperature. Will obtain a clear solution.
Weigh oil (Coconut Oil, Palm Oil, Olive Oil, Corn Oil, Soybean Oil ...) according to the recipe.
Pour oil was weighed into a blender.
Carefully pour the solution in NaOH / KOH into the oil.
Put cover blender, put the cloth on top of the cover was to avoid splashing and processes at the lowest round. Lest Avoid splashing into your face or body. Stop the blender and check the soap to see the stage "trace". "Trace" is a condition in which the soap has been formed and is the end of the mixing process. The sign is when the soap mixture begins to thicken. When touched with a spoon, then spoon a few seconds before the former still made an impression, that's why it is called "trace".
At the time of "trace" before you can add fragrances, dyes or additives. Stir a few seconds then stop round blender.
Pour the soap results into a mold. Cover with a cloth for insulation. Keep the soap in the mold last for one to two days. Then remove it from the mold, cut to taste. Keep at least 3 weeks before use.
* Explanation of how the number 1 for safety.
Sodium Hydroxide (NaOH) / Sodium Hydroxide / lye / caustic soda / caustic soda is the main ingredient in the manufacture of soap other than oil. Through a chemical reaction, NaOH changed the oil or fat into soap. Addition of NaOH is also necessary to make shampoo and body lotion.
In making lye (NaOH + water), there are some things that should be considered include:
Use long sleeves, goggles, masks and rubber gloves. Precautionary principle - attention is necessary because the fluid can cause blindness if splashed in eyes, or cause a burning sensation on the skin when. Also provide vinegar, this is to anticipate when the skin is exposed to the alkaline liquid.
Do it in an open space, such as in a park or in a place that has free air. Do not breathe the air that comes out of this solution.
Always include into the water (slowly) and not vice versa. If you do otherwise, would result in outbreaks that are dangerous to skin and eyes.
Keep out of reach of children - children / do not involve children - children at all.
Step By Step How To Make Recycled Paper By Hand And Machine
The process of making Recycled Paper Manual
A. How to Manual
Preparing or making paper into paperboard waste paper or craft paper can be done manually with a simple tool that can be of our own making.
Some materials that can be used to make paperboard including sludge or waste paper, waste paper, water hyacinth, banana leaves, straw, waste cane. The tools to make the paper, among others.
Screen printing or sieve gauze:
- Gauze Alternatively framed picture
Rakel screen printing:
- Paint roll alternatively opened the absorption section (left the pralon)
- Bucket or vessel, attempted size larger than the size of screen printing
- Grey cloth, nylon or as an alternative to using cloth banners former
- Mat board or flat
- Blender
- Foam
Materials - Materials Pulp:
- Paper waste (sludge): An alternative waste newspaper
- Glue Starch: can be made by mixing flour with hot water
Preparation:
Prepare place-mat tool for process printing, collated printing section with the sequence of the bottom section up to the top as follows:
- Board / mat, 30-45 degrees slope position
- Foam
- Fabric
Step - Step execution:
A. Making paper (Pulp)
As the material for recycling paper we take the example of old newspapers, some steps such as:
- Soak old newspapers in the water for 2 days to get looks broken, try water cover all parts of the paper.
- Having seen melted or destroyed, blender with water in the ratio 1:4 to form paper.
- Mix the starch with glue paper to the blender
- Entry and prepare the dough into a large container or bucket with water adjusted to add air. Wanted a printout paper thin, the addition of water can be reproduced (more dilute, the job gets thinner)
- The dough is ready to be printed
B. Print Paper Carton
Once the pulp mixture is ready, then we do the printing paper in the following way :
- Enter the fully submerged screen printing and strain until the dough is ready in a bucket / container screen printing frame below.
- Lift the frame, and make sure the filter paper pulp mixture evenly over the screen. (The filter is the result of mold in wet conditions)
- Drain the water dripping frame to maximum.
- Once that's a little trickle of water / dry, remove and put into print fabric prints that have been prepared with the dough sticking to the position of the filter cloth
- Dry the filter paper and attach it to the screen until the water Rakel - really dry or thinning
- Gently lift screen printing, and will look half-finished paperboard
- Wind - air the prints for about half hour then dried in the sun
- If it is completely dry, take the paper from the fabric and iron to get average results.
- Trim with cut out sides
B. Rework Machine With
Process in processing or recycling of paper with the actual engine is a development of the manual method.
Processing by machine will be very helpful in terms of effectiveness in terms of time and effort.
As with any manual work, an outline or pattern process is almost the same.
Some parts machining among which are:
- The process of making pulp or paper : This process is done in the machine bitter / Hollander.
- Printing Process: Worked on a Fourier machine, i.e cartons printing machine
- Drying Process: As with the manual method, the process is still using solar energy
- Flattening process: If the manual processing by the board, with the machine using the machine calendar.
- Cutting process: Working with paper cutting machines.
A. How to Manual
Preparing or making paper into paperboard waste paper or craft paper can be done manually with a simple tool that can be of our own making.
Some materials that can be used to make paperboard including sludge or waste paper, waste paper, water hyacinth, banana leaves, straw, waste cane. The tools to make the paper, among others.
Screen printing or sieve gauze:
- Gauze Alternatively framed picture
Rakel screen printing:
- Paint roll alternatively opened the absorption section (left the pralon)
- Bucket or vessel, attempted size larger than the size of screen printing
- Grey cloth, nylon or as an alternative to using cloth banners former
- Mat board or flat
- Blender
- Foam
Materials - Materials Pulp:
- Paper waste (sludge): An alternative waste newspaper
- Glue Starch: can be made by mixing flour with hot water
Preparation:
Prepare place-mat tool for process printing, collated printing section with the sequence of the bottom section up to the top as follows:
- Board / mat, 30-45 degrees slope position
- Foam
- Fabric
Step - Step execution:
A. Making paper (Pulp)
As the material for recycling paper we take the example of old newspapers, some steps such as:
- Soak old newspapers in the water for 2 days to get looks broken, try water cover all parts of the paper.
- Having seen melted or destroyed, blender with water in the ratio 1:4 to form paper.
- Mix the starch with glue paper to the blender
- Entry and prepare the dough into a large container or bucket with water adjusted to add air. Wanted a printout paper thin, the addition of water can be reproduced (more dilute, the job gets thinner)
- The dough is ready to be printed
B. Print Paper Carton
Once the pulp mixture is ready, then we do the printing paper in the following way :
- Enter the fully submerged screen printing and strain until the dough is ready in a bucket / container screen printing frame below.
- Lift the frame, and make sure the filter paper pulp mixture evenly over the screen. (The filter is the result of mold in wet conditions)
- Drain the water dripping frame to maximum.
- Once that's a little trickle of water / dry, remove and put into print fabric prints that have been prepared with the dough sticking to the position of the filter cloth
- Dry the filter paper and attach it to the screen until the water Rakel - really dry or thinning
- Gently lift screen printing, and will look half-finished paperboard
- Wind - air the prints for about half hour then dried in the sun
- If it is completely dry, take the paper from the fabric and iron to get average results.
- Trim with cut out sides
B. Rework Machine With
Process in processing or recycling of paper with the actual engine is a development of the manual method.
Processing by machine will be very helpful in terms of effectiveness in terms of time and effort.
As with any manual work, an outline or pattern process is almost the same.
Some parts machining among which are:
- The process of making pulp or paper : This process is done in the machine bitter / Hollander.
- Printing Process: Worked on a Fourier machine, i.e cartons printing machine
- Drying Process: As with the manual method, the process is still using solar energy
- Flattening process: If the manual processing by the board, with the machine using the machine calendar.
- Cutting process: Working with paper cutting machines.
Step By Step How To Make A Kite
Buy or make your own? Here are ways to make it:
Prepare the following materials:
1 piece of bamboo with a thin width + / - 1 cm and a length of + / - 80 cm, 1 piece of reed thin with a width of + / - 1 cm and a length of + / - 40 cm, tissue paper or wax paper to size according to the size of the reed, gam, ribbon rolls rather thick, rope or yarn, scissors, gam, paper "tracing"
How to Make:
Put the two crossed bamboo with a meeting point at one third of the longest bamboo bamboo Embed both by using a rope or thread.
Tie and plug it into four side reed with string or yarn to form a diamond. Now the order is complete kite, then put the kite frame on paper.
Sign the paper so that the shape of the kite frame. Add an extra 2.5 cm to the line of pieces.
The paper scissors following the line of the piece.
Fold the paper towards the back, and then attach to the frame using the gam.
For balance, add the tail of the rope or yarn about 1 meter long, tie the bottom portion kite. Step beyond, adding cutouts for jewelry.
Make a hole in the middle of the kite (close to crossing a bamboo frame) enter the kite string or yarn to the hole and tie to the crossover point, then another to tie the side under the framework of kites (long rope about 90cm).
Prepare the following materials:
1 piece of bamboo with a thin width + / - 1 cm and a length of + / - 80 cm, 1 piece of reed thin with a width of + / - 1 cm and a length of + / - 40 cm, tissue paper or wax paper to size according to the size of the reed, gam, ribbon rolls rather thick, rope or yarn, scissors, gam, paper "tracing"
How to Make:
Put the two crossed bamboo with a meeting point at one third of the longest bamboo bamboo Embed both by using a rope or thread.
Tie and plug it into four side reed with string or yarn to form a diamond. Now the order is complete kite, then put the kite frame on paper.
Sign the paper so that the shape of the kite frame. Add an extra 2.5 cm to the line of pieces.
The paper scissors following the line of the piece.
Fold the paper towards the back, and then attach to the frame using the gam.
For balance, add the tail of the rope or yarn about 1 meter long, tie the bottom portion kite. Step beyond, adding cutouts for jewelry.
Make a hole in the middle of the kite (close to crossing a bamboo frame) enter the kite string or yarn to the hole and tie to the crossover point, then another to tie the side under the framework of kites (long rope about 90cm).
Sabtu, 24 Agustus 2013
Step By Step How To Make Paper
Paper is a basic requirement of modern humans today. Almost in all institutions in all aspects of life using paper. Ranging from paper, container / place products, arts, entertainment, and so on.However, the use of so much paper that resulted in many trees are cut down to create paper. Not to mention the other benefits of trees to people who also lead to a 'loss' drastically tree from this earth. In fact, besides the wood consumed by humans, we also (surely!) requires oxygen which is supplied by the plant. Moreover, we have used the paper will be a waste if we do not make use of jelly it wasted. Honey is not it?So, let's take advantage of waste paper!The trick?There are many. One way is to recycle paper. If
you do not know, how to stay looking in the search engines with the
keyword 'make recycled paper' and yes, there is a result. Much.Of
the paper recycling procedures, the majority (if not all) site mentions
that we need objects called screen printing to print and you do not
know what the object was. You do not know what it is screen printing? Well, I myself do not know. Our series.
Well, yesterday I tried to make recycled paper with reckless capital:
Now, I make it like this:
Results recycled paper if you can again according to taste. If I am, I make recycled paper as a binder contents.
Well, yesterday I tried to make recycled paper with reckless capital:
- Any waste paper.
- Bucket or basin, which is important to to hold liquid.
- A plastic knife or ruler to flatten.
- Water.
- Tea strainer that meeting.
- Former board.
- Non shirt rags. There are two. Length of the cloth to cover the former board until the board trace all closed. In order not to loose you can use duct tape. The other fabric (not necessarily wide) to squeeze out the pulp.
- pandanus palms, is optional. One site that I make reference practice makes recycled paper mentions that the pandanus palms be used as a natural green coloring and it turned out it was not true. When I tried it myself, pandanus palms can scent the paper (but faint aroma) and give 'ornaments' mottled green color in the finished paper.
- Mortar belong to my mother. Mortar can also (for those who have). Actually I want to use the blender anyway. But, since blender difficult to clean and feed electrical energy, finally I use a mortar. Not bad, can make hand exercise.
- Starch (which is cheap). The same could be replaced or wood glue paper glue. Whatever glue, starch / glue should be diluted with water first so it does not clot.
- Pot. If you can use the former in order to avoid confusion pot if you want to cook.
- Stove.
- Spoon and spoon rest.
- Containers and other containers.
Now, I make it like this:
- Insert the paper into the water, torn up into small pieces that resemble pulp, soak overnight to fade the ink,
- Filter porridge with tea strainer. Take the waste (pulp) and squeezed until it hardens so 'rock' paper,
- This paper set stone then ground with a mortar. As a result, rock paper so that eventually crushed garlic odor,
- Fill the pan with a paper that had been crushed, water, leaves are pulverized, and the cornflour mixed with water at a dose that will. Bring to a boil on the stove, stirring constantly until the watery pulp yield and fragrant with a texture somewhat sticky like glue. Oh, yeah, if added leaves, onion aroma that sticks in the paper can be neutralized,
- Pulp squeezed disposable cloth until not too watery. Place on a board that is already covered in cloth,
- The pulp then flattened by hand or with a plastic knife (so the smooth) until smooth,
- Winds to dry. Do not dry in direct sunlight so that the paper is not bent when dry. Try also drying so that it takes up not using electrical energy,
- Dry! remove the cloth from the paper slightly. Please make it more smoothly ironed.
Results recycled paper if you can again according to taste. If I am, I make recycled paper as a binder contents.
Step By Step How To Make Tempeh Easy And Practically
Tempeh is the best alternative source of nutrition. The price is cheap and it tastes delicious make tempeh never lose loyal customers. Basically, tempeh is made from soybeans fermented grains with certain drying. However, in certain areas there is not some kind of tempeh is made from soybeans. For example, in the area where the dam Kedungombo tempeh is made from the seeds of his trademark surly or Macuna Mucuna Kara. In the area of East Bali Lombok, tempeh is made from bean dregs pigeon peas with soybean gembus name. In another Malang, called tempeh tempeh Majas and made of mixed peanuts and coconut. Still there are many variants of tempeh. But in general, tempeh consumption of soy ranks highest in Indonesia. If you have been used to buy tempeh in the market, there is no harm in this time you make tempeh right from your home. The trick is fairly easy. The material is also only two: Soybean Seed and Leaven. Dare to try?Making steps TempehTo make tempeh, the very first step to prepare course materials and tools needed. As for the materials required as follows:
How to make tempeh as follows:
First, boil water to boil. Then enter soybeans into boiling water earlier. Let stand until water temperatures warm. Furthermore, separate water and soy beans. Then knead until beans separated from the chaff and bean split into two.
Soybeans that have been separated from the skin re-boiled with water until the froth. After that, separate the soybeans with water. For faster dry, store in a container of soy beans were essentially flat has been given a cloth to absorb the liquids.
Once dry, soybeans stored in sunken container. Then add yeast and flour. Stir until completely evenly.
Once completely mixed, put into a medium soy plastic or banana leaves. Ends sealed plastic or banana leaves. Then make the plastic a small holes in its so there is air circulation for.
Allow the dough tempeh with a duration of 24 to 36 hours. Better yet, if stored in a warm place.How? How to make tempeh is very easy and practical, right? With a little patience and seriousness, you can make as a business opportunity tempeh economic support your family. Good luck!
- Soybeans as much as 2 kg.
- sago or tapioca flour 1 tablespoon.
- Tempeh 1 tablespoon.
- Pot to boil.
- Sunken container or bowl.
- flat container.
- Plastic or banana leaves.
How to make tempeh as follows:
First, boil water to boil. Then enter soybeans into boiling water earlier. Let stand until water temperatures warm. Furthermore, separate water and soy beans. Then knead until beans separated from the chaff and bean split into two.
Soybeans that have been separated from the skin re-boiled with water until the froth. After that, separate the soybeans with water. For faster dry, store in a container of soy beans were essentially flat has been given a cloth to absorb the liquids.
Once dry, soybeans stored in sunken container. Then add yeast and flour. Stir until completely evenly.
Once completely mixed, put into a medium soy plastic or banana leaves. Ends sealed plastic or banana leaves. Then make the plastic a small holes in its so there is air circulation for.
Allow the dough tempeh with a duration of 24 to 36 hours. Better yet, if stored in a warm place.How? How to make tempeh is very easy and practical, right? With a little patience and seriousness, you can make as a business opportunity tempeh economic support your family. Good luck!
Langganan:
Postingan (Atom)