Step 1
Drill two small holes on each side of the wooden hoops .
Step 2 FebruaryThen paint all your circles in black wood.
Step 3 MarchOnce your circles are dry, go google '' moon phases. '' If you find an image / graphic that shows in every phase of the moon pressure. This will help you to keep track of what each stage looks like .Then start painting each moon phase with the gray color. I have to give a little glitter, shine my gray moons.
Step 4 AprilIf your moon is dry, you can begin to connect them. To do this , simply cut a small piece of embroidery thread and feed each end on the back of your two wooden hoops . Then tie a knot in the front. Repeat this step until all the moons are connected .
Once all your moons are connected , go and some embroidery thread for '''' black moons at each end of your banner . This will create loops to hang your banner.
Minggu, 15 Desember 2013
Selasa, 12 November 2013
Step By Step How To Make A Toy Car Used Bottle Guide
Hardware Requirements:
- 1 piece of plastic bottles
- 4 piece crown corks (for tires)
- 2 pieces of straw
- Tape
How to:
(Adding a straw). 1.Holes bottle front and rear body
Break Part 2 of straw. Straws, an eye which had been cut in the last two bottles.
3.Turn the cap before masing2 perforated suction side.
Place 4.After crown straw. Straws and strips on a bit thick coat. End so that the tires are not easily separated.
5.Paste integral straw on the back of the car. During the processing of the car.
Best of luck!
- 1 piece of plastic bottles
- 4 piece crown corks (for tires)
- 2 pieces of straw
- Tape
How to:
(Adding a straw). 1.Holes bottle front and rear body
Break Part 2 of straw. Straws, an eye which had been cut in the last two bottles.
3.Turn the cap before masing2 perforated suction side.
Place 4.After crown straw. Straws and strips on a bit thick coat. End so that the tires are not easily separated.
5.Paste integral straw on the back of the car. During the processing of the car.
Best of luck!
Selasa, 05 November 2013
Step By Step How To Make Wooden Toy Cars
Hardware Requirements:
- Wood
How to:
1.First prepare the ingredients.
2.Split and cut wood with a circular saw type serkel model.
3.Give shape pattern on wood.
Wooden model 4.Tack given by Jet saw chainsaw.
5.cleaning the flat surface, so that the timber with glass paper alternator.
6.Gluing one with the other wood surfaces with wood glue.
Use 7.Shape, smooth body paper alternator glass.
8.Give holes with a drill.
9.Make a wheel with a wood lathe.
10.Sublimate the surface, after all phases with a fine sandpaper finish.
11.Finishing spray by spraying the surface with a compressor melamine.
Best of luck!
- Wood
How to:
1.First prepare the ingredients.
2.Split and cut wood with a circular saw type serkel model.
3.Give shape pattern on wood.
Wooden model 4.Tack given by Jet saw chainsaw.
5.cleaning the flat surface, so that the timber with glass paper alternator.
6.Gluing one with the other wood surfaces with wood glue.
Use 7.Shape, smooth body paper alternator glass.
8.Give holes with a drill.
9.Make a wheel with a wood lathe.
10.Sublimate the surface, after all phases with a fine sandpaper finish.
11.Finishing spray by spraying the surface with a compressor melamine.
Best of luck!
Senin, 28 Oktober 2013
Step By Step How To Make Homemade Gift Box Beautiful
Hardware Requirements:
- Rice Box (can be bought in the supermarket)
- Adhesive paper / double top
- Insulation / adhesive glue
- The wrapping paper can be replaced with a washcloth jg
- Article
- Pencil
- Knife charter
- As a band, small flowers, dolls, or something in a unique form flannel Suspended
How to:
Gift box shape, good for beginners or 1.Specify square triangle.
2.make box or model.
3.then cut the housing.
4.Shape and unite the configuration box with insulation.
5.if done? To stick a box or double top at the top of the box inside and out, and provide background information.
6.Then gently turn the gift box.
7.Give double bottom box jga edge and cover with white paper.
If the valve is substantially covered with wrapping paper and then give up beautiful decorations
Best of luck!
- Rice Box (can be bought in the supermarket)
- Adhesive paper / double top
- Insulation / adhesive glue
- The wrapping paper can be replaced with a washcloth jg
- Article
- Pencil
- Knife charter
- As a band, small flowers, dolls, or something in a unique form flannel Suspended
How to:
Gift box shape, good for beginners or 1.Specify square triangle.
2.make box or model.
3.then cut the housing.
4.Shape and unite the configuration box with insulation.
5.if done? To stick a box or double top at the top of the box inside and out, and provide background information.
6.Then gently turn the gift box.
7.Give double bottom box jga edge and cover with white paper.
If the valve is substantially covered with wrapping paper and then give up beautiful decorations
Best of luck!
Senin, 21 Oktober 2013
Step By Step How To Make A Simple Fan
Hardware Requirements:
- switch
- Black and red cable 1m
- 2 x 1.5 V
- The battery
- Dynamo
- Sheets - Sheets bottle Aqua
- Black insulation
- Screwdriver (+) and (-)
How to:
1.Put a 1.5 V battery in the battery compartment, then cut the bottom of the bottle and forms such as AQUA knives - knives, only 4 sections.
2.Wrap the son of red and black copper in the switch.
Buyer 3.Others battery nothings, the red wire to the (-) terminal of the battery and the black wire to the (+) of the battery first, but open to the buyer.
4 The battery cable is coupled, attached to the anchor member
5.Plug knife - knife on the alternator.
6.Make all conditions as previously directed.
Best of luck!
- switch
- Black and red cable 1m
- 2 x 1.5 V
- The battery
- Dynamo
- Sheets - Sheets bottle Aqua
- Black insulation
- Screwdriver (+) and (-)
How to:
1.Put a 1.5 V battery in the battery compartment, then cut the bottom of the bottle and forms such as AQUA knives - knives, only 4 sections.
2.Wrap the son of red and black copper in the switch.
Buyer 3.Others battery nothings, the red wire to the (-) terminal of the battery and the black wire to the (+) of the battery first, but open to the buyer.
4 The battery cable is coupled, attached to the anchor member
5.Plug knife - knife on the alternator.
6.Make all conditions as previously directed.
Best of luck!
Step By Step How To Make A Wooden Bowl
Equipment and materials required:
- A fresh wood
- An ax
How to make :
1.Slit wood through the middle of the wood.
2.Select the perfect piece of wood you want. Make 2 pieces of fruit in your assessment on the handle of the bowl , as shown
in the image. Do not cut too deep. Then cut pieces that you have created on the base of the handle , before you can do to make the image of the shell. Now handle future what you want based .
3.Doing sculpture continuously until you are satisfied with the shape of your dish.
4.for timber pieces in a bowl is long enough
Thus, the strategy if you are busy, always when you cut a little time with your record Newspapers plastic to make it moist and not dry as it would make it harder for you drier Now it's time for a bowl cut you with a knife, and it may take a little time to dedicate the sculpture forms and you will soon know if you do get your hands perfectly capable of this. there
5.Place your work in an open bag for over a week , because if you do not, your chances are wooden bowl
dry quickly and the wood will last split.Hal you need to do is to stay
Grinding of the shell with sand paper starts from the rough , then smooth .
Best of luck !
- A fresh wood
- An ax
How to make :
1.Slit wood through the middle of the wood.
2.Select the perfect piece of wood you want. Make 2 pieces of fruit in your assessment on the handle of the bowl , as shown
in the image. Do not cut too deep. Then cut pieces that you have created on the base of the handle , before you can do to make the image of the shell. Now handle future what you want based .
3.Doing sculpture continuously until you are satisfied with the shape of your dish.
4.for timber pieces in a bowl is long enough
Thus, the strategy if you are busy, always when you cut a little time with your record Newspapers plastic to make it moist and not dry as it would make it harder for you drier Now it's time for a bowl cut you with a knife, and it may take a little time to dedicate the sculpture forms and you will soon know if you do get your hands perfectly capable of this. there
5.Place your work in an open bag for over a week , because if you do not, your chances are wooden bowl
dry quickly and the wood will last split.Hal you need to do is to stay
Grinding of the shell with sand paper starts from the rough , then smooth .
Best of luck !
Sabtu, 31 Agustus 2013
Step By Step How To Make A Simple Fan
Materials needed :
- Switches
- Black and red cables 1m
- 2 batteries 1,5 V
- The battery
- Dynamo
- Blades - blades of aqua bottle
- Isolation Black
- Screwdriver (+) and (-)
How to Make :
1.Put a 1.5 V battery in the battery compartment, then cut the bottom of the bottle and forms such as aqua blades - blades, just 4 sections.
2.Wrap the copper red and black wires in the switch.
3.Other copper tacked on battery, the red wire attached to the pole (-) battery, and the black wire attached to the pole (+) battery cable first but opened, until you see the copper.
4.The cable has been connected battery is attached to the armature
5.Plug blades - blades on the dynamo.
6.Make sure all the circumstances as directed previously.
Good luck!
- Switches
- Black and red cables 1m
- 2 batteries 1,5 V
- The battery
- Dynamo
- Blades - blades of aqua bottle
- Isolation Black
- Screwdriver (+) and (-)
How to Make :
1.Put a 1.5 V battery in the battery compartment, then cut the bottom of the bottle and forms such as aqua blades - blades, just 4 sections.
2.Wrap the copper red and black wires in the switch.
3.Other copper tacked on battery, the red wire attached to the pole (-) battery, and the black wire attached to the pole (+) battery cable first but opened, until you see the copper.
4.The cable has been connected battery is attached to the armature
5.Plug blades - blades on the dynamo.
6.Make sure all the circumstances as directed previously.
Good luck!
Step By Step How To Make A Beautiful Wooden Bowl
Equipment and materials required :
- A fresh wood
- An ax
How to Make :
1.Slit the wood by taking the midpoint of the wood.
2.Select the ideal piece of wood and you like. Make 2 pieces of fruit according to your estimates to the handle of the bowl as shown
in the image. Do not cut too deep. Then sectioned pieces that you created earlier to form the basis of the handle you can make the picture of the bowl. Now grip bowl according to what you want.
3.Doing carving continuous until you are satisfied with your dish shape.
4.For carved wood pieces into a bowl takes a fairly long time,
so the strategy if you are busy, do continuously if you have a little time with your record store logs in plastic in order to keep it moist and not dry, as if it would make you more dry difficult to carve! Now it's time to carve a bowl with a carving knife you, and this may spend some time to form carving and you will soon find out if your hands quite adept at doing this.
5.Place your work in an open bag for more than a week, because if you do not do it, chances are your wooden bowl
will dry too quickly and the wood will last split.Hal you need to do is stay
sanding the bowl with sand paper starts from the rough and then use smooth.
Good luck!
- A fresh wood
- An ax
How to Make :
1.Slit the wood by taking the midpoint of the wood.
2.Select the ideal piece of wood and you like. Make 2 pieces of fruit according to your estimates to the handle of the bowl as shown
in the image. Do not cut too deep. Then sectioned pieces that you created earlier to form the basis of the handle you can make the picture of the bowl. Now grip bowl according to what you want.
3.Doing carving continuous until you are satisfied with your dish shape.
4.For carved wood pieces into a bowl takes a fairly long time,
so the strategy if you are busy, do continuously if you have a little time with your record store logs in plastic in order to keep it moist and not dry, as if it would make you more dry difficult to carve! Now it's time to carve a bowl with a carving knife you, and this may spend some time to form carving and you will soon find out if your hands quite adept at doing this.
5.Place your work in an open bag for more than a week, because if you do not do it, chances are your wooden bowl
will dry too quickly and the wood will last split.Hal you need to do is stay
sanding the bowl with sand paper starts from the rough and then use smooth.
Good luck!
Step By Step How To Make Candle Decorative Candle Of Time
Materials and Tools needed :
- Remnants of wax used (more colors, the better)
- Small size glass
- Wick candles (can be purchased at craft stores)
- Markers water proof
- Cutter
How to Make :
1.Slice Used to smooth wax granules like sand.
2.Decorative glass with writing or pictures with a waterproof marker.
3.Enter the wick while the wax flakes pour chopped fine earlier in the glass. Condense to a solid back and the wick upright. If you are multicolored candles, it can put wax flakes slices alternating with another color. Condense back up to full.
4.Now your candle wax appearance to be different than usual. More beautiful because it is packaged in a glass that has been painted with markers color water proof you.
- Remnants of wax used (more colors, the better)
- Small size glass
- Wick candles (can be purchased at craft stores)
- Markers water proof
- Cutter
How to Make :
1.Slice Used to smooth wax granules like sand.
2.Decorative glass with writing or pictures with a waterproof marker.
3.Enter the wick while the wax flakes pour chopped fine earlier in the glass. Condense to a solid back and the wick upright. If you are multicolored candles, it can put wax flakes slices alternating with another color. Condense back up to full.
4.Now your candle wax appearance to be different than usual. More beautiful because it is packaged in a glass that has been painted with markers color water proof you.
Step By Step How To make A Crafts Sandals Pinch Of Materials Used Paint
Materials and tools needed :
- Plain flip-flops
- Oil paint
- Varnish
- Brushes
- Pencil
- Hair dryer. If no, can use the fan.
How to Make:
1.Decide what image you want to paint over your old flip flops. Select the images that simple, that is not difficult if you are a beginner to paint a portrait of affairs. The pictures suggested as pictures of flowers, stars, leaves or hearts.
2.Use a pencil to make a drawing first.
3.Once your finished image created with a pencil. Now seal your image with oil paint using a brush. Populate field with color sandals until there is no field in the top of the sandal that looks empty.
4.After all the top pedestal colored flip flops, dry with hair dryer or can also with the help of a fan.
5.Once completely dry. Cover picture that you paint over the top of the sandal footwear you had with spray varnish. Use varnish in order to eventually become more shiny appearance. Then, re-dry.
- Plain flip-flops
- Oil paint
- Varnish
- Brushes
- Pencil
- Hair dryer. If no, can use the fan.
How to Make:
1.Decide what image you want to paint over your old flip flops. Select the images that simple, that is not difficult if you are a beginner to paint a portrait of affairs. The pictures suggested as pictures of flowers, stars, leaves or hearts.
2.Use a pencil to make a drawing first.
3.Once your finished image created with a pencil. Now seal your image with oil paint using a brush. Populate field with color sandals until there is no field in the top of the sandal that looks empty.
4.After all the top pedestal colored flip flops, dry with hair dryer or can also with the help of a fan.
5.Once completely dry. Cover picture that you paint over the top of the sandal footwear you had with spray varnish. Use varnish in order to eventually become more shiny appearance. Then, re-dry.
Step By Step How To Make Pinch Of Pretty Rag Time
Materials and Tools needed :
- Flip flops plain
- Patchwork
- pencil
- scissors
- Glue gun
- Knick-knacks supporters. Can use the rest of the buttons are large if there is.
How to Make:
1.Put your flip flops over patchwork. It's the point that you can make cuts in the size of flip-flops pattern to the base. Draw the pattern with a pencil, and scissors.
2.Following the pattern of your footwear neat scissors, match the size patchwork at the top of your flip flops footwear. Do not forget, give a little hole in the middle and the two left and right side that strap sandals tongs not block patchwork to be affixed.
3.Paste patchwork scissors and you have your last match at the top of the flip-flops footwear using a glue gun. Remember, be careful using this type of glue because if exposed hands will feel the heat. Press and trim patchwork to cover all parts of the flip-flops footwear before, except strap clip.
4.To the strap flip-flops that have not been exposed to the touch patchwork, you simply cut the leftover patchwork size 3 cm width and length can be customized with your big flip-flops.
5.Give the glue on the strap flip-flops, then wrap the rest of the neat patchwork that has been cut to a width of 3 cm was in flip flops strap you to cover all parts of the strap clip.
6.Once all parts of your flip flops neatly covered with patchwork, except the bottom of the sandal, now you just add sweetener accessories for your flip-flops. Attach buttons former multicolored large strap on one side of your flip-flops.
Good luck!
- Flip flops plain
- Patchwork
- pencil
- scissors
- Glue gun
- Knick-knacks supporters. Can use the rest of the buttons are large if there is.
How to Make:
1.Put your flip flops over patchwork. It's the point that you can make cuts in the size of flip-flops pattern to the base. Draw the pattern with a pencil, and scissors.
2.Following the pattern of your footwear neat scissors, match the size patchwork at the top of your flip flops footwear. Do not forget, give a little hole in the middle and the two left and right side that strap sandals tongs not block patchwork to be affixed.
3.Paste patchwork scissors and you have your last match at the top of the flip-flops footwear using a glue gun. Remember, be careful using this type of glue because if exposed hands will feel the heat. Press and trim patchwork to cover all parts of the flip-flops footwear before, except strap clip.
4.To the strap flip-flops that have not been exposed to the touch patchwork, you simply cut the leftover patchwork size 3 cm width and length can be customized with your big flip-flops.
5.Give the glue on the strap flip-flops, then wrap the rest of the neat patchwork that has been cut to a width of 3 cm was in flip flops strap you to cover all parts of the strap clip.
6.Once all parts of your flip flops neatly covered with patchwork, except the bottom of the sandal, now you just add sweetener accessories for your flip-flops. Attach buttons former multicolored large strap on one side of your flip-flops.
Good luck!
Step By Step How To Make A Simple Steam Engine
Materials needed :
- Bit of wire, for turbine shaft.
- Pipe, can be anything as long as it is bent and heat resistant.
- Several former tin drinks, to make the boiler (where heat the water to evaporate) and its burner.
- Glue or glue iron G.
- Paint, to enhance the results.
- Plywood, as its base plate.
- Nut bolts (should not wear this, can directly glue), to buffer the boiler.
- Spirits, to fuel burner.
For equipment we just need (equipment may not be complete, the risk can be broken hand):
- Hacksaw, for sawing plywood or tin.
- Cutter (Choose large enough to easily do it), to cut the cans.
- Pliers, for bending pipe.
- Scissors, to make turbine of thin tin plate.
How to Make :
1. Close all the holes in the tin first, then puncture in the skin of the hull at each end. Function 1 hole to fill holes while the heated water for 2 to remove the fumes. 1 hole can be given a piece of pipe to make it more organized once made ??the cover so that when the last steam evaporation process is not out of the entry of liquid fluid (water).
2. Create a suitable turbine "greet skills" as well as its own lid to be like the black and white image above.
3. Do not forget to glue each component to be connected unless the exhaust holes (exhaust) to absolutely no holes.
4. Make it from the burner cans.
5. Then paint and laid out as you wish and use the fill water to evaporate in advance and enjoy the sensation of pleasure.
- Bit of wire, for turbine shaft.
- Pipe, can be anything as long as it is bent and heat resistant.
- Several former tin drinks, to make the boiler (where heat the water to evaporate) and its burner.
- Glue or glue iron G.
- Paint, to enhance the results.
- Plywood, as its base plate.
- Nut bolts (should not wear this, can directly glue), to buffer the boiler.
- Spirits, to fuel burner.
For equipment we just need (equipment may not be complete, the risk can be broken hand):
- Hacksaw, for sawing plywood or tin.
- Cutter (Choose large enough to easily do it), to cut the cans.
- Pliers, for bending pipe.
- Scissors, to make turbine of thin tin plate.
How to Make :
1. Close all the holes in the tin first, then puncture in the skin of the hull at each end. Function 1 hole to fill holes while the heated water for 2 to remove the fumes. 1 hole can be given a piece of pipe to make it more organized once made ??the cover so that when the last steam evaporation process is not out of the entry of liquid fluid (water).
2. Create a suitable turbine "greet skills" as well as its own lid to be like the black and white image above.
3. Do not forget to glue each component to be connected unless the exhaust holes (exhaust) to absolutely no holes.
4. Make it from the burner cans.
5. Then paint and laid out as you wish and use the fill water to evaporate in advance and enjoy the sensation of pleasure.
Step By Step How To Make A Wallet Out Of Fabric
Tools and materials required :
- 2 pieces of fabric for the outside of the wallet, it's up to the desired size. Mine are 20cm x 12cm
- 2 pieces of fabric to the inside, the same size
- 1 piece zipper 20 cm, can be cut if too long
- Scissors, thread, pin
- Sewing Machine
How to Make :
1. Bring fabric lining inside good side facing up, zipper facing up, and the outer layer of the fabric good side facing down (so both sides meet each other good). Shifted so as not to use the help of a pin.
2. Then sewing, and through the fabric so that the good side facing out.
3. Then repeat steps 1 and 2 on the other side of the zipper.
4. Once sewn and reversed.
5. Unite each side of the outer fabric and good inside.
6. then sew the left and right edges.
7. Sew the top edge and also the lower edge, make sure the zipper is opened when sewing each edge. reserving a little to flip open cloth wallet (not stitched full).
8. Behind purse through the open space behind.
9. Close the gap that opens with stitching, input the inside, and the wallet is ready for use.
Good luck!
- 2 pieces of fabric for the outside of the wallet, it's up to the desired size. Mine are 20cm x 12cm
- 2 pieces of fabric to the inside, the same size
- 1 piece zipper 20 cm, can be cut if too long
- Scissors, thread, pin
- Sewing Machine
How to Make :
1. Bring fabric lining inside good side facing up, zipper facing up, and the outer layer of the fabric good side facing down (so both sides meet each other good). Shifted so as not to use the help of a pin.
2. Then sewing, and through the fabric so that the good side facing out.
3. Then repeat steps 1 and 2 on the other side of the zipper.
4. Once sewn and reversed.
5. Unite each side of the outer fabric and good inside.
6. then sew the left and right edges.
7. Sew the top edge and also the lower edge, make sure the zipper is opened when sewing each edge. reserving a little to flip open cloth wallet (not stitched full).
8. Behind purse through the open space behind.
9. Close the gap that opens with stitching, input the inside, and the wallet is ready for use.
Good luck!
Step By Step How To Make Cold Powder
Materials needed:
- Rice flour (1 cup)
- Yam flour (1 cup)
- Fragrant Water Moderation
How to Make:
Material No. 1 and 2 mixed into one, then mixed with material No. 3 while in roller-roller until creamed like making cookie dough, just being dense dough. The powder made ??round object like a lizard eggs kept in the sun to dry.
Good luck!
- Rice flour (1 cup)
- Yam flour (1 cup)
- Fragrant Water Moderation
How to Make:
Material No. 1 and 2 mixed into one, then mixed with material No. 3 while in roller-roller until creamed like making cookie dough, just being dense dough. The powder made ??round object like a lizard eggs kept in the sun to dry.
Good luck!
Step By Step How To Make Traditional Body Scrub For Whitening Face Naturally
- Rice Scrub
Rice is no stranger to use as an alternative to whiten skin naturally. Rice contains Squalid oil, vitamin C, and vitamin E. Rice is the most effective way to whiten skin is Japanese rice. The rice has a higher vitamin content that is more effective than local rice.
However, that does not mean you can not use local rice because local rice you can also use. To make a scrub of rice, prepare rice which will be made into a scrub suit your taste.
After that, wash and soak the rice. Puree rice by way of fine rice pounded and mixed with rose water. Shape the dough into small round - small and basking in the sun to dry.
Once dry, you can take some seeds and mix it with water until it becomes a paste for use on the face. Apply evenly to the face and let stand until dry, or about 30 minutes. After that, rinse with clean water. Do this regularly to get maximum results.
- Scrub Yam
Yam is one of the most widely used fruits for skin whitening products. The content of the yam pieces able lighten skin naturally. If you want to whiten skin with yam, you can make it yourself at home.
How to Make :
Prepare 1 piece of yam that has been peeled clean skin. Then, wash thoroughly and grated yam according to the amount you need. After that, apply the results of grated yam in the face evenly. Let stand about - about 40 minutes and wash thoroughly.
- Tomato and Lime
Both of these fruits contain vitamin C which is very high and also antioxidants that can reduce free radicals. Vitamin C is believed to brighten the skin pigment, so the skin becomes white. To make a facial scrub of tomato and lime, prepare 1 large tomato and a lemon. Cut tomatoes up into several parts.
Then put tomatoes in a blender and add the lemon juice. Once blended, the dough used as a mask on the face. Let stand for 30 minutes and rinse with water until clean. If your skin is sensitive because the vitamin C content of orange juice is high enough, you can use the tomatoes alone.
Good luck!
Rice is no stranger to use as an alternative to whiten skin naturally. Rice contains Squalid oil, vitamin C, and vitamin E. Rice is the most effective way to whiten skin is Japanese rice. The rice has a higher vitamin content that is more effective than local rice.
However, that does not mean you can not use local rice because local rice you can also use. To make a scrub of rice, prepare rice which will be made into a scrub suit your taste.
After that, wash and soak the rice. Puree rice by way of fine rice pounded and mixed with rose water. Shape the dough into small round - small and basking in the sun to dry.
Once dry, you can take some seeds and mix it with water until it becomes a paste for use on the face. Apply evenly to the face and let stand until dry, or about 30 minutes. After that, rinse with clean water. Do this regularly to get maximum results.
- Scrub Yam
Yam is one of the most widely used fruits for skin whitening products. The content of the yam pieces able lighten skin naturally. If you want to whiten skin with yam, you can make it yourself at home.
How to Make :
Prepare 1 piece of yam that has been peeled clean skin. Then, wash thoroughly and grated yam according to the amount you need. After that, apply the results of grated yam in the face evenly. Let stand about - about 40 minutes and wash thoroughly.
- Tomato and Lime
Both of these fruits contain vitamin C which is very high and also antioxidants that can reduce free radicals. Vitamin C is believed to brighten the skin pigment, so the skin becomes white. To make a facial scrub of tomato and lime, prepare 1 large tomato and a lemon. Cut tomatoes up into several parts.
Then put tomatoes in a blender and add the lemon juice. Once blended, the dough used as a mask on the face. Let stand for 30 minutes and rinse with water until clean. If your skin is sensitive because the vitamin C content of orange juice is high enough, you can use the tomatoes alone.
Good luck!
Step By Step How To Make Origami Paper Flower
Tools and materials required:
- Paperboard
- Paper asturo
- Decorative Paper
- Sticks to taste
- Scissors
- Glue
- Pencil
- ruler
- Term
How to Make:
1.Make flower pattern on paper asturo. Then the paper folded, cut into 2, and again cut into small pieces to size. Paper that has been cut out and then glued and taped to the stick shaft. Once the paper is folded down.
3.Use a ruler and pencil to make a flower leaf pattern on paper asturo. Paper scissors according to the pattern that was made. Make a circle with a period of 4 pieces. Large size, medium, and small.
4.Rekatkan smallest circle paper on stem sticks. Prepare a pattern that is so, then arranged to form a circle. Then continue with the remaining paste flower patterns on the flower pattern that has been prepared. Attach a large piece of the circle to the flower arrangement that has been assembled. Then attach the pieces are the size of the circle to the smallest circle.
5.Cut the decorative paper with a size of 5 cm in the longitudinal direction. Decorative paper cut in a circle attached to the rod that has been given a glue stick. Flower arrangement that has been made, then attached to the stem sticks. Press firmly to be attached.
6.Origami paper flowers you've finished and ready to be used as decoration.
Good luck!
- Paperboard
- Paper asturo
- Decorative Paper
- Sticks to taste
- Scissors
- Glue
- Pencil
- ruler
- Term
How to Make:
1.Make flower pattern on paper asturo. Then the paper folded, cut into 2, and again cut into small pieces to size. Paper that has been cut out and then glued and taped to the stick shaft. Once the paper is folded down.
3.Use a ruler and pencil to make a flower leaf pattern on paper asturo. Paper scissors according to the pattern that was made. Make a circle with a period of 4 pieces. Large size, medium, and small.
4.Rekatkan smallest circle paper on stem sticks. Prepare a pattern that is so, then arranged to form a circle. Then continue with the remaining paste flower patterns on the flower pattern that has been prepared. Attach a large piece of the circle to the flower arrangement that has been assembled. Then attach the pieces are the size of the circle to the smallest circle.
5.Cut the decorative paper with a size of 5 cm in the longitudinal direction. Decorative paper cut in a circle attached to the rod that has been given a glue stick. Flower arrangement that has been made, then attached to the stem sticks. Press firmly to be attached.
6.Origami paper flowers you've finished and ready to be used as decoration.
Good luck!
Step By Step How To Make Statue Of Soap
Materials needed:
- Soap or soap bars
- Knife table or can be replaced with a plastic knife for the cake (avoid using a sharp knife that can harm children)
- Ballpoint pen or pencil
- Water and a towel or tissue
How to Make :
1.Hold soap by hand and make sure the position as comfortable as possible. Use a knife to carve out areas that are not occupied by the hand. The most convenient way is to form a hand on the soap as shown above. It might help to trace a line to the hand soap and then carve it. Or it could also create other forms of appropriate children imagination, develop course. Examples such as Angry Birds form below baseline. After hand shape already seen, the child does not have to hold the soap in hand again. Continue to carve soap positioned in place by the child comfortable to do so. Put your hands back to the soap if necessary.
2.Shape accordance with that thought in the beginning (before the sample form of the hand).
3.The completed, the sculpture can be smoothed with wetted and rubbed gently with a towel or cloth.
4.Letting dried and finished.
Good luck!
- Soap or soap bars
- Knife table or can be replaced with a plastic knife for the cake (avoid using a sharp knife that can harm children)
- Ballpoint pen or pencil
- Water and a towel or tissue
How to Make :
1.Hold soap by hand and make sure the position as comfortable as possible. Use a knife to carve out areas that are not occupied by the hand. The most convenient way is to form a hand on the soap as shown above. It might help to trace a line to the hand soap and then carve it. Or it could also create other forms of appropriate children imagination, develop course. Examples such as Angry Birds form below baseline. After hand shape already seen, the child does not have to hold the soap in hand again. Continue to carve soap positioned in place by the child comfortable to do so. Put your hands back to the soap if necessary.
2.Shape accordance with that thought in the beginning (before the sample form of the hand).
3.The completed, the sculpture can be smoothed with wetted and rubbed gently with a towel or cloth.
4.Letting dried and finished.
Good luck!
Step By Step How To Make Flowers For Skin Lotion
Materials needed :
- 2 teaspoons of coconut oil
- 1 cup of boiled water
- 1 teaspoon of essential oil
- 2 tablespoons of flower petals and the cake is dried (can use roses, jasmine, or lavender)
How to Make:
1.Take dried flowers, place in bowl. Mix with boiled water. Put it in the oven for 30 minutes.
2.Remove from oven flower water, then grab some spoons and mix with coconut oil and essential oils. Stir for a few minutes until completely mixed water and oil.
3.Sweep on the skin. Essential oils usually take up to 5 minutes for absorption by the body.
Good luck!
- 2 teaspoons of coconut oil
- 1 cup of boiled water
- 1 teaspoon of essential oil
- 2 tablespoons of flower petals and the cake is dried (can use roses, jasmine, or lavender)
How to Make:
1.Take dried flowers, place in bowl. Mix with boiled water. Put it in the oven for 30 minutes.
2.Remove from oven flower water, then grab some spoons and mix with coconut oil and essential oils. Stir for a few minutes until completely mixed water and oil.
3.Sweep on the skin. Essential oils usually take up to 5 minutes for absorption by the body.
Good luck!
Step By Step How To Make Yo-Yo
1.Every half of the plastic yo-yo started as two parts: the part, which would bring the flat inner shaft is called the disk, and the outer spherical shell called (type butterfly yo-yo is the opposite, with a flat round disk and shell. This is done through the same process but on a separate assembly line). Plastic used to make the disc and put shells in the form of solid pellets into a large funnel with a screw in equally large. The outside of the funnel covered with a flexible strip called the band heaters, electric blankets are like narrow for a funnel. Each band will be getting warmer as the narrow funnel, and a screw pushing pellets into the bottom of the funnel, they become more and more fluid. This process ensures that the pellets will melt evenly and completely, which is very important for the next step. At the bottom of the funnel, screw pushing molten plastic into the mold through a tube called a gate.
2.In the mold is the form of the four discs and four shells, all connected to the gate. This mold has a valve, allowing hot air to be pushed out to the front of the plastic and make sure that the mold completely.
Wooden yo-yo made from wood that has been dried to ensure your own yo-yo will not change shape. Modern wooden model has two sections of wood connected by a metal shaft.
Because the mold is fully charged and because the plastic has completely melted and evenly, each shell and each disc will always be perfectly round and perfectly even have a weight distribution. Once the mold is filled, plastic holding for 17 seconds and cool down with a water-filled tube running along the outside of the mold. Then the mold, which is actually two parts clamped tightly together, releasing shells and parts, all connected by a filled plastic gate, to the assembly line to be formed to yoyo section.
3.In while molding line is to make yo-yo parts, axles cutting machine apart to connect them. The engine is fed a long piece of round metal. Exact length of the metal to make the shaft is inserted into clamp where it was cut. Pieces are then cut notched at both ends so it will grip the plastic.
4.After mold release palm shells and discs, a separate clip their workers, eliminating the extra plastic and snapped them together to make a piece. Each disk has a lip shell and matching the pieces are free. When the plastic is still slightly warm from the mold, the lip will snap together. Once tied, they will not release.
5.This part derived belts for machines called hot stamper. The hot stamper has a circular tray with cup-like holders around the side. Each holder of taking half yo-yo and spin into a heated press. Press any roll feed logo yo-yo will show to the top half of the yo-yo. Then pressed into half and heats logo, affixing logos. Another design using round inserts the appropriate logo into the disk and the shell so that the insert can be seen clearly.
6.Part to continues down the line on workers who put the axle in half and set it with a hammer. The next worker put the other half on top and set it with a hammer. Then assembled yoyo placed in the air-driven press. The press has a tray in the form of yo-yo and a metal plate that fits between the yoyo part. The metal plate has grooves cut to fit around the axle and the exact thickness of the gap between the manufacturer's specified parts. When the press fire, it's good to permanently secure the two parts of the axle and set the correct gap between sections.
7.So The yo-yo is now placed on the table with a coiled rope and cutter at one end and upright, with a few notches in it at the other end. The distance between the cutter and the exact length of erect length string for each manufacturer wants yo-yo. String is pulled from the spool through the notch in the upright, where he circled the shaft of the yo-yo. Then pulled back into the cut, cutter, and bound. Yo-yo then left her hanging from a string, which is organized by the notch in the upright, turning to the axle.
8.Swing the yo-yo moves down the line to a machine that resembles a miniature turntable. A worker puts yo-yo at the wheel, holding it down with one hand, holding the tension in the string with your other hand, and with a foot switch operated, rotating to the yo-yo string.
9.Packaging yo-yo for a card called skin. Leather cards are pieces of cardboard with the product attached to it with what appeared to be melted plastic wrap you see hanging in store displays. To package the way yo-yo's, a piece of card tucked under a piece of wood with a hole in it in accordance with the card below. A yo-yo dropped through each hole to card. This ensures correct placement on the card. The sheet is then moved to the feed roller machine plastic film over the entire sheet of card and yo-yo. The film is made of a special plastic that fits every shape and shrink when heated but not melted. Machine heats the plastic, tightly seal the yo-yo to the card. The machine then cut the sheet into individual cards and rotate them into the basket where they are collected and boxed for shipment.
Good luck!
2.In the mold is the form of the four discs and four shells, all connected to the gate. This mold has a valve, allowing hot air to be pushed out to the front of the plastic and make sure that the mold completely.
Wooden yo-yo made from wood that has been dried to ensure your own yo-yo will not change shape. Modern wooden model has two sections of wood connected by a metal shaft.
Because the mold is fully charged and because the plastic has completely melted and evenly, each shell and each disc will always be perfectly round and perfectly even have a weight distribution. Once the mold is filled, plastic holding for 17 seconds and cool down with a water-filled tube running along the outside of the mold. Then the mold, which is actually two parts clamped tightly together, releasing shells and parts, all connected by a filled plastic gate, to the assembly line to be formed to yoyo section.
3.In while molding line is to make yo-yo parts, axles cutting machine apart to connect them. The engine is fed a long piece of round metal. Exact length of the metal to make the shaft is inserted into clamp where it was cut. Pieces are then cut notched at both ends so it will grip the plastic.
4.After mold release palm shells and discs, a separate clip their workers, eliminating the extra plastic and snapped them together to make a piece. Each disk has a lip shell and matching the pieces are free. When the plastic is still slightly warm from the mold, the lip will snap together. Once tied, they will not release.
5.This part derived belts for machines called hot stamper. The hot stamper has a circular tray with cup-like holders around the side. Each holder of taking half yo-yo and spin into a heated press. Press any roll feed logo yo-yo will show to the top half of the yo-yo. Then pressed into half and heats logo, affixing logos. Another design using round inserts the appropriate logo into the disk and the shell so that the insert can be seen clearly.
6.Part to continues down the line on workers who put the axle in half and set it with a hammer. The next worker put the other half on top and set it with a hammer. Then assembled yoyo placed in the air-driven press. The press has a tray in the form of yo-yo and a metal plate that fits between the yoyo part. The metal plate has grooves cut to fit around the axle and the exact thickness of the gap between the manufacturer's specified parts. When the press fire, it's good to permanently secure the two parts of the axle and set the correct gap between sections.
7.So The yo-yo is now placed on the table with a coiled rope and cutter at one end and upright, with a few notches in it at the other end. The distance between the cutter and the exact length of erect length string for each manufacturer wants yo-yo. String is pulled from the spool through the notch in the upright, where he circled the shaft of the yo-yo. Then pulled back into the cut, cutter, and bound. Yo-yo then left her hanging from a string, which is organized by the notch in the upright, turning to the axle.
8.Swing the yo-yo moves down the line to a machine that resembles a miniature turntable. A worker puts yo-yo at the wheel, holding it down with one hand, holding the tension in the string with your other hand, and with a foot switch operated, rotating to the yo-yo string.
9.Packaging yo-yo for a card called skin. Leather cards are pieces of cardboard with the product attached to it with what appeared to be melted plastic wrap you see hanging in store displays. To package the way yo-yo's, a piece of card tucked under a piece of wood with a hole in it in accordance with the card below. A yo-yo dropped through each hole to card. This ensures correct placement on the card. The sheet is then moved to the feed roller machine plastic film over the entire sheet of card and yo-yo. The film is made of a special plastic that fits every shape and shrink when heated but not melted. Machine heats the plastic, tightly seal the yo-yo to the card. The machine then cut the sheet into individual cards and rotate them into the basket where they are collected and boxed for shipment.
Good luck!
Step By Step How To Make A Bike Out Of Bamboo
1. Cutting Bamboo
Cut off the bamboo as a bike frame material very easily, far different from steel or other metal cutting. We just need a regular saws, abrasives, epoxy resin and natural fibers. Next, show the next working step.
2. Assemble Frame
Connecting bamboo sticks that have been cut into the bike frame, is the most difficult step for the workshop participants. Each bamboo bike makers have different methods. There is a wrap around frame that has been assembled with natural fiber sheets. Others use the connection joints of steel.
3. Wrap Frame
To make the connection stronger frame, bamboo wrapped in cloth from natural fibers. The way the aviation industry in developing bamboo grafting techniques. Use of hemp fiber composite material previously dyed epoxy resin.
4. Original Bamboo More
There is a motto "original steel frame bike is". Steel frame of the bike is touted provide the best quality while driving. Riding a bamboo bike frame mentioned more comfortable.
Good Luck!
Cut off the bamboo as a bike frame material very easily, far different from steel or other metal cutting. We just need a regular saws, abrasives, epoxy resin and natural fibers. Next, show the next working step.
2. Assemble Frame
Connecting bamboo sticks that have been cut into the bike frame, is the most difficult step for the workshop participants. Each bamboo bike makers have different methods. There is a wrap around frame that has been assembled with natural fiber sheets. Others use the connection joints of steel.
3. Wrap Frame
To make the connection stronger frame, bamboo wrapped in cloth from natural fibers. The way the aviation industry in developing bamboo grafting techniques. Use of hemp fiber composite material previously dyed epoxy resin.
4. Original Bamboo More
There is a motto "original steel frame bike is". Steel frame of the bike is touted provide the best quality while driving. Riding a bamboo bike frame mentioned more comfortable.
Good Luck!
Langganan:
Postingan (Atom)